Reset service light indicator Renault Safrane. How to reset maintenance light, reset oil service light. Can be made manually by use button on car dash board.
Reset service light indicator Renault Safrane. It was built in years: 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000.
1. The reset button is located on the bottom right hand side of the Rev counter on the instrument cluster.
2. Turn ON the ignition, do not start the vehicle.
3. Push reset button until Spanner warning light symbol will start flash.
4. Keep button depressed until Spanner warning light symbol stops flashing and remains illuminated.
5. Indicator shows appropriate service interval.
6. Release reset button.
7. Turn OFF the ignition and then start your Renault Sfrane to see if spanner warning light has been reset.
Note. Some vehicles are fitted with a SERV lamp, this is not a service interval indicator lamp, it is a malfunction indicator lamp (MIL).
2009-2011
1. Push the ignition switch to the ON position (do not start the engine). Use the ENTER button (?) and toggle the vehicle information display to show the SETTING screen. Use the NEXT button (?) to select.
2. Use the NEXT button (?) to select MAINTENANCE
i) SETTING > MAINTENANCE > OIL > ENGINE OIL to set or reset the mileage for the engine oil change.
ii) SETTING > MAINTENANCE > FILTER > to set or reset the mileage for the engine oil filter.
3. Turn the ignition off and then start the engine to verify the indicator has been reset.
2007-2012
1. Turn the ignition to position 1. (close all doors
2. Press the system selection button (3 located on the lower left of the steering wheel) repeatedly until the kilometer or temperature reading is shown in the multi information display.)
3. Press the TRIP reset button (center button on instrument panel) quickly 3 times. An audible beep will be heard followed by the battery voltage displayed.
4. Press the scoll forward/back button (left side of steering wheel) to highlight the “”Service menu””.”
5. Use the +/- buttons to select “”Confirmation”” menu. Press the system select button to confirm. The menu item “”Complete service”” is highlighted.”
6. Press the system selection button to confirm. “”Service confirmed”” appears.”
7. Use the scroll forward/back button to exit the menu.
8. Turn the ignition off and then start the engine to verify the indicator has been reset.
2006-2012
1. Turn the ignition to position 1. (close all doors
2. Press the system selection button (3 located on the lower left of the steering wheel) repeatedly until the kilometer or temperature reading is shown in the multi information display.)
3. Press the TRIP reset button (center button on instrument panel) quickly 3 times. An audible beep will be heard followed by the battery voltage displayed.
4. Press the scoll forward/back button (left side of steering wheel) to highlight the “”Service menu””.”
5. Use the +/- buttons to select “”Confirmation”” menu. Press the system select button to confirm. The menu item “”Complete service”” is highlighted.”
6. Press the system selection button to confirm. “”Service confirmed”” appears.”
7. Use the scroll forward/back button to exit the menu.
8. Turn the ignition off and then start the engine to verify the indicator has been reset.
2010-2012
1. Turn the ignition to position 1. (close all doors
2. Press the system selection button (left button on left steering wheel controls) repeatedly until the kilometer reading is shown in the multi information display.)
3. Press the system selection button (located on the far left of the steering wheel) repeatedly until the menu item “”trip”” with highlighter is stored in the multi-function display. *Trip remains selected for 5 seconds so you need to move to step 4.”
4. First press and hold the accept phone call button and within 1 second also press and hold the OK button for 5 seconds. The workshop menu will appear in the display showing “”vehicle data
5. Press the scroll forward button (lower button on left steering wheel controls) to highlight “”ASSYST PLUS”” and then confirm by pressing OK button.”
6. Press scroll forward button (lower button on left steering wheel controls) to highlight “”Full Service”” and then confirm by pressing OK button.”
7. Press scroll forward button until “”YES”” is highlighted and confirm swith OK button. “”No take-back possible”” appears.”
8. Press scroll forward button until “”Confirmation”” is highlighted and confirm with OK button. “”Full service carried out”” appears.”
9. Press OK button and back button (standalone button on left steering wheel controls) repeatedly until the menus are exited.
10. Turn the ignition off and then start the engine to verify the indicator has been reset.