Reset service light indicator Renault Safrane. How to reset maintenance light, reset oil service light. Can be made manually by use button on car dash board.
Reset service light indicator Renault Safrane. It was built in years: 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000.
1. The reset button is located on the bottom right hand side of the Rev counter on the instrument cluster.
2. Turn ON the ignition, do not start the vehicle.
3. Push reset button until Spanner warning light symbol will start flash.
4. Keep button depressed until Spanner warning light symbol stops flashing and remains illuminated.
5. Indicator shows appropriate service interval.
6. Release reset button.
7. Turn OFF the ignition and then start your Renault Sfrane to see if spanner warning light has been reset.
Note. Some vehicles are fitted with a SERV lamp, this is not a service interval indicator lamp, it is a malfunction indicator lamp (MIL).
Reset service light indicator Renault Scenic 2. From year: 2003, 2004, 2005, 2006, 2007, 2008, 2009.
How to reset service light indicator Renault Scenic 2.
1. Turn the ignition to ON position 2, don’t start the vehicle.
2. On cars with keycard ignition, insert the card, then push & hold the start button for 5 seconds to turn on the dashboard cluster lights.
3. Push & button on the end of the wiper stalk repeatedly until the warning spanner symbol and miles to service appears on the monitor, some models have 2 buttons, which cycle through the options in opposite directions, either button can be used in this case.
4. Push & hold the button.
5. The display will now change to the new service interval and start flashing.
6. Keep holding the button until the display stops flashing.
7. Release the button, turn ignition to off and start the car to see if warning light has been reset.
Well after a small but required service on the car I had to reset the warning light. The real quick deal to reset all the requested lights on Rover 75 is to do the following
Get a small wire, Turn the key to second position, Short Pin 8 and Pin 4 on the OBD connector for “4 seconds to reset oil light”, “8-25 seconds for the other 2 lights” and this will reset the 15000 service request for oil change. Quick and easy and not legal if you do it without actually doing the service.
2004
Turn the ignition to run (one position before starting engine).
Press ODO/TRIP button to display odometer mode. Turn ignition off.
While pressing ODO/TRIP button, turn ignition to run (one position before starting engine). Continue to hold the button for longer than 5 seconds.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2005-2006
Turn the ignition to run (one position before starting engine).
Push the “TRIP” button to change the trip meter display to blank. Turn the ignition off.
While pressing the trip meter “RESET” button, turn ignition to run (one position before starting engine). Continue to hold the button for longer than 5 seconds.
“Mileage Reset” appears on the display, the master warning light comes on, and a warning tone sounds.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2007
Turn the ignition to run (one position before starting engine). Use the trip meter switch to bring up the trip meter A reading.Turn the ignition off.
While pressing the trip meter reset button, set the engine switch to run (one position before starting engine) and continue to press and hold the knob until the multi information display indicates that the reset is complete.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2008-2010
Turn the engine on. Use the trip meter switch to bring up the trip meter A reading. Turn the ignition off.
While pressing the trip meter reset button, set the engine switch to run (push START/ STOP button once) and continue to press and hold the knob until the multi information display indicates that the reset is complete.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2004-2006
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the trip meter reset knob then the turn ignition off.
Hold down the trip meter reset knob while turning the ignition key to the run position (one position before starting engine).
Hold down the knob until the light goes off. Before the light goes off, it illuminates 3 seconds, flashes for 2 seconds and illuminates for 1 second. If the system fails to reset, the light will remain flashing. In this case, return to step 1 and try again.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2007-2009
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the trip meter reset knob then the turn ignition off.
Hold down the trip meter reset knob while turning the ignition key to the run position (one position before starting engine).
Keep pressing the knob until the ěMAINT REQDî light goes off. If the light continues flashing, return to step 1 and try again.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2010
Turn the ignition to run – engine off (push START/STOP button once).
Press the Menu switch to change the multi-information display to blank. Turn the engine off.
While pressing the ODO/TRIP button, set the ěENGINE START STOP” switch to run – engine off (push START/STOP button once).
Keep pushing the ěODO/TRIPî switch for more than 7 seconds. While doing this operation, the master warning light comes on, a warning tone sounds and the “RESETTING OIL MAINTENANCE DATA” message appears to inform you that light has been reset. After 5 seconds, the system reset is completed.
Turn the ignition off and then start the engine to verify the indicator has been reset.