Reset maintenance light on Dodge Sprinter
1. Put the key in the ignition and switch it on without starting the engine.
(Wait for LCD to return to the vehicle mileage)
2. Hold the “O” button down till you hear a beep (could take a while, 30 sec.)
3. Press the M button repeatedly and a number of reset menus will appear, (If you have used oil according to quality sheet 229.31 or 228/229.51 you can scroll to Reset.31 or Reset.51 respectively.) Select “reset 51″
4. Now, when appropriate oil type is selected press “O” for 6 seconds until ”2” is displayed.
5. Press “O” once again briefly and the ” reset done” message will confirm that the job is done.
6. Pull the Key out
FOR THE 2004 DODGE SPRINTER!
Turn the key to position 2 in the ignition lock and immediately press the button MI (km) twice.
Within 10 seconds, return the key to the 0 in the ignition lock.
Press and hold the button MI (km). Turn the key to position 2 in the ignition lock. Keep the button MI (km) pressed.
The maintenance indicator with the time/distance is shown.
After about 10 seconds, an acoustic signal will sound and the maintenance indicator is displayed with the new remaining time / distance .
Release the button MI (km)
1. Turn your ignition key to the ‘ACC’ or ‘LOCK’ position.
2. Press and hold the trip meter reset nob (next to your Toyota Land Cruiser’s odometer).
3. While holding the trip meter reset nob, turn the ignition to ‘ON’, but do not start your Toyota Land Cruiser.
4. Hold the meter reset until the MAINT REQD light switches off.
If this procedure does not successfully reset your maintenance required light, make sure that your digital odometer is set with the odometer reading showing and try again. If the light is still lit, you can try disconnecting your Toyota Land Cruiser battery, causing the internal computer to reset. If you still haven’t successfully turned off the oil indicator MAINT REQD light, please read your manual or contact your dealer for further instruction!
1. Put the key in the ignition and switch it on without starting the engine.
(Wait for LCD to return to the vehicle mileage)
2. Hold the “O” button down till you hear a beep (could take a while, 30 sec.)
3. Press the M button repeatedly and a number of reset menus will appear, (If you have used oil according to quality sheet 229.31 or 228/229.51 you can scroll to Reset.31 or Reset.51 respectively.) Select “reset 51”
4. Now, when appropriate oil type is selected press “O” for 6 seconds until ”2” is displayed.
5. Press “O” once again briefly and the ” reset done” message will confirm that the job is done.
6. Pull the Key out
FOR THE 2004 DODGE SPRINTER!
Turn the key to position 2 in the ignition lock and immediately press the button MI (km) twice.
Within 10 seconds, return the key to the 0 in the ignition lock.
Press and hold the button MI (km). Turn the key to position 2 in the ignition lock. Keep the button MI (km) pressed.
The maintenance indicator with the time/distance is shown.
After about 10 seconds, an acoustic signal will sound and the maintenance indicator is displayed with the new remaining time / distance .
Release the button MI (km)
Engine Oil Change Indicator System
Oil Change Required
Your vehicle is equipped with an engine oil change
indicator system. The “Oil Change Required” message
will flash in the EVIC display for approximately 10
seconds after a single chime has sounded to indicate the
next scheduled oil change interval. The engine oil change
indicator system is duty cycle based, which means the
engine oil change interval may fluctuate dependent upon
your personal driving style.
Unless reset, this message will continue to display each
time you turn the ignition switch to the ON/RUN
position. To turn off the message temporarily, press and
release the MENU button. To reset the oil change indicator
system (after performing the scheduled maintenance)
refer to the following procedure.
1. Turn the ignition switch to the ON position (Do not
start the engine).
2. Fully depress the accelerator pedal slowly three times
within 10 seconds.
3. Turn the ignition switch to the OFF/LOCK position.
NOTE: If the indicator message illuminates when you
start the vehicle, the oil change indicator system did not
reset. If necessary repeat this procedure.
2008
Turn the ignition key to OFF.
Press the instrument panel cluster stem until the odometer is displayed.
Press and hold the cluster stem until the letters “InSP” are displayed.
Hold the cluster stem down and turn the ignition key to RUN (one position before starting engine).
The letters “InSP” in the instrument panel cluster display will flash.
Keep the cluster stem down for at least 20 seconds and then release the stem. If the letters “InSP” and the remaining mileage for the next oil change appear in the instrument panel cluster display, the system is properly reset. Turn the ignition off and then start the engine to verify the indicator has been reset.
2009
Turn the ignition key to LOCK/OFF.
Press the instrument panel cluster stem until the odometer is displayed, then release the stem.
Re-press and hold the cluster stem until the letters “InSP” are displayed.
Press and hold the brake pedal down, hold the cluster stem down, and turn the ignition key to RUN (one position before starting engine).
The letters “InSP” in the instrument panel cluster display will flash.
Keep the cluster stem down for at least 10 seconds and release the stem and the brake pedal when the message “new remaining mileage” is displayed. Turn the ignition off and then start the engine to verify the indicator has been reset.