2007-2010
Turn the ignition to (II) – do not start the engine.
Press the SEL/RESET button on the steering wheel repeatedly until engine oil life is displayed.
Press and hold the SEL/RESET button for more than 10 seconds. The remaining engine oil life reset mode will be shown on the multi information display.
Select RESET by pressing the INFO (▲/▼) button, then press the SEL/RESET button to reset the engine oil life display. The maintenance item code(s) will disappear, and the engine oil life will reset to 100.
Turn the ignition off and then start the engine to verify the indicator has been reset.
*Models equipped with the keyless access system have an engine start/stop button instead of an ignition switch. Pushing start/stop button once without starting engine is equivalent of ignition (II).
2001-2005
Turn the key to off position.
Press and hold the SELECT and RESET buttons on the instrument panel and turn the ignition to position (II) – do not start the engine.
Hold the SELECT and RESET buttons until the indicator resets, hold for about 10 seconds.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2006-2010
Turn the ignition to (II) – do not start the engine.
Press the SEL/RESET button on the steering wheel repeatedly until engine oil life is displayed.
Press and hold the SEL/RESET button for more than 10 seconds. The remaining engine oil life reset mode will be shown on the multi information display.
Select RESET by pressing the INFO (▲/▼) button, then press the SEL/RESET button to reset the engine oil life display. The maintenance item code(s) will disappear, and the engine oil life will reset to 100.
Turn the ignition off and then start the engine to verify the indicator has been reset.
*Models equipped with the keyless access system have an engine start/stop button instead of an ignition switch. Pushing start/stop button once without starting engine is equivalent of ignition (II).
2006-2010
Turn the ignition to (II) – do not start the engine.
Press the SEL/RESET button on the steering wheel until you see the engine oil life display.
Press and hold the SEL/RESET button on the steering wheel for more than 10 seconds. The remaining engine oil life reset mode will be shown on the multi information display.
Select RESET by pressing the INFO (▲/▼) button, then press the SEL/RESET button to reset the engine oil life display. The maintenance item code(s) will disappear, and the engine oil life will reset to 100.
Turn the ignition off and then start the engine to verify the indicator has been reset.
solved the problem, i found a TSB explaing what to do when this happens, and than i found a realy good HOW TO.
Practicly you need to reset the hand brake cylinder by:
1. Disconect batery for 5 minutes (this means if your car is 2007> you will have to go to dealer so he can put the code for radio thru some GEKO system othervise you cant use the radio!)
2. Connect the batery.
3. Dont start the car only give contact (many lights go on )
4. pres and hold the brake while presing the hand brake 2 times on and 2 times off. (i waited 30 seconds betven “on” and “off” cause the manual i found wasnt very clear)
5. Than i pussehd the cylinder back with hands, (Be carful not to turn it!!!) only push it straight i did it by hand.
6. Put everything back, deleted the fault codes and started all over again like manual said on the previous post.
I did everything like it said but at the end i end up with P on the dash light up, than i only deleted the fault codes from controler 53 – Hand brake and it worked like a charm!
Instructions
Things You’ll Need
Wrench
Ignition key
OBDl or ll scanner
1. Disconnect your battery cables from the battery posts with a 6-pt. closed wrench in the size appropriate for the battery bolts. Remove the negative (black) cable first. Leave the battery disconnected for several minutes, according to Allpar.com. Reconnect, this time starting with the positive cable, and crank the engine. The code should be gone.
2. Crank the Jeep. Drive it forward, then backwards, and shut off. Repeat this procedure three times. The codes should clear on the fourth crank.
3. Use a OBDl or OBDll scan tool. Plug the tool into your Jeep’s ALDL (Assembly Line Diagnostic Link), a small, rectangular electrical port usually located under the dash. Turn the key to the “on” position. Scan the computer for codes and select the option to clear the codes.
4. Wait for the code to clear itself automatically. Once the component is fixed, the check engine light disappears after several successful ignitions. The code is then stored for a while. If the engine continues to start and run without a re-occurrence of the original problem, the code is wiped out.