Instructions
1. Open the hood and loosen the retaining nut on the cable clamp running to the negative battery terminal.
2. Slide the clamp off of the negative battery terminal.
3. Wait 1 minute for the Range Rover’s electronic control module to cycle and reset. Then, reconnect the clamp to the negative battery terminal.
4. Tighten the retaining nut on the cable clamp. The airbag light should go out at this point. When it does, you’ll know that the fault code has been erased.
2000-2005
Turn the ignition off.
Press and hold the TRIP METRE RESET button while you turn the ignition switch to run (one position before starting engine).
Continue holding the button until the indicator resets (indicator light goes out).
Turn the ignition off and then start the engine to verify the indicator has been reset.
2006
Turn the ignition to run (one position before starting engine).
Press the TRIP button until the engine oil life indicator is displayed.
Press the trip button for more than 10 seconds. The engine oil life indicator and the maintenance items code(s) will blink.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2007
Turn the ignition to run (one position before starting engine).
Press the TRIP button until the engine oil life indicator is displayed.
Press the trip button for more than 10 seconds. The engine oil life indicator and the maintenance items code(s) will blink.
Press the TRIP button for more than 5 seconds. The maintenance items code(s) will disappear, and the engine oil life will reset to “100”.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2006-2008
Turn the ignition to run (one position before starting engine).
Press the SELECT button repeatedly until the engine oil life display or the service message is displayed.
Press the RESET button for about 10 seconds. You will see a “MAINT RESET” message.
Select the appropriate answer, “MAINT RESET N” (NO) OR “MAINT RESET Y” (YES) by pressing the SELECT button repeatedly. “N” or “Y” is displayed on the outside temperature display.
Select the ëëMAINT RESET Yíí (YES), and press and hold the RESET button again to reset the engine oil life to 100.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2009-2010
Turn the ignition to run (one position before starting engine).
Press the SELECT/RESET knob repeatedly until the engine oil life indicator is displayed.
Press the SELECT/RESET knob for more than 10 seconds. The engine oil life indicator and the maintenance code(s) will blink.
Press the SELECT/RESET knob for more than 5 seconds. The maintenance items code(s) will disappear, and the engine oil life will reset to 100.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2003-2005
Turn off the engine.
Press and hold the SELECT/RESET button in the instrument panel and turn the ignition switch to run (one position before starting).
Hold the button for at least 10 seconds, until the indicator resets.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2006-2010
Turn the ignition to run (one position before starting engine).
Press the SELECT/RESET knob repeatedly until the engine oil life indicator is displayed.
Press the SELECT/RESET knob for more than 10 seconds. The engine oil life indicator and the maintenance code(s) will blink.
Press the SELECT/RESET knob for more than 5 seconds. The maintenance items code(s) will disappear, and the engine oil life will reset to 100.
Turn the ignition off and then start the engine to verify the indicator has been reset.
1995-1999
With Reset Button on Instrument Panel:
Turn off the engine.
Press and hold the SELECT/RESET button in the instrument panel and turn the ignition switch to run (one position before starting).
Hold the button for at least 10 seconds, until the indicator resets.
Turn the ignition off and then start the engine to verify the indicator has been reset.
With Key Slot on Instrument Panel:
Reset the coloured indicator by inserting your key in the slot beside the indicator.
2000-2004
Turn off the engine.
Press and hold the SELECT/RESET button in the instrument panel and turn the ignition switch to run (one position before starting).
Hold the button for at least 10 seconds, until the indicator resets.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2005-2010
Turn the ignition to run (one position before starting engine).
Press the SELECT/RESET knob repeatedly until the engine oil life indicator is displayed.
Press the SELECT/RESET knob for more than 10 seconds. The engine oil life indicator and the maintenance code(s) will blink.
Press the SELECT/RESET knob for more than 5 seconds. The maintenance items code(s) will disappear, and the engine oil life will reset to 100.
Turn the ignition off and then start the engine to verify the indicator has been reset.