1. To reset MAINT reminder light after engine oil replacement, turn ignition switch to OFF position with odometer showing ODOMETER READING. Turn ignition switch to ON position while holding down trip meter RESET button.
2. Hold trip meter RESET button down for at least 5 seconds until odometer indicates “000000” and MAINT reminder light goes out.
Put the key into the ignition and turn it to position “I.”
Press the trip odometer button in and hold it. Turn the ignition key to position “II.”
Wait about 5 seconds until the service engine light begins to blink. After the 4th blink, turn the ignition key back to position “I.”
Release the button and start the engine. The light should have turned off. If not, repeat steps 1 through 4 again.
BMW 2001 to current
Ignition Off (Position 0)
Press and Hold the trip odometer button while turning key to position 1 (ACCESSORY)
Keep the button depressed (about 5 secs.) until you see “Oil Service” or “Inspection” with “Reset” or “Re” in the display*
Press the button again and hold for approx. 5 secs. until “Reset” or “Re” flashes
While the display is flashing, briefly press the button again to reset the Service Interval. After the display has shown the new interval you should see “END SIA” for about 2 seconds
Note: that if the “Reset” or “Re” does not flash, then you have not met the minimum consumption level and cannot reset
*Note: On vehicles with “High” cluster, you will also see the amount of fuel (in litres) remaining until next service
Volvo 1999-2000 – S / V / C70 Models
Press and Hold odometer reset button
Turn ignition switch to “run” position
After SRL flashes, release odometer reset button
Turn ignition off
Turn ignition back on to confirm reset
Volvo 1998 – S80 Models
Turn ignition switch to position 1
Press and hold the odometer reset button
Turn ignition switch to position 2
Wait until service light blinks and then release odometer button
Volvo 1999-2000 – S80 Models
Turn ignition switch to position 1
Press and hold “day counter reset button”
Turn ignition switch to position 2
Continue holding day counter for approx. 10 seconds
After SRL flashes, release day counter button
Should hear “beep-beep” to confirm command accepted
Volvo 2001 – XC 70 Models
The following steps must be completed with no longer than 5 seconds between each step:
Make sure the trip meter is in T-1
Turn ignition key to position 1
Press and hold trip meter button until zero is shown
While still holding the trip meter, turn key to position 2
When original trip mileage returns, release the trip reset button
Turn key to off
How to reset the Maintenance Service interval:
Metod 1
– Switch ignition on to position one, (first click clockwise);
– “Outside temperature” should be displayed, if not move to it (You have to be in this display to go further);
– Press the trip odometer, “reset”, knob three times consecutively ( The Voltage display will appear);
– Press Down Arrow to enter the “Service Menu”. “Service Data” submenu below will be highlighted.
– Press right page to enter the Service data submenu. (Left page goes up in menus, -+ selects items displayed)
– Press – three times on right of wheel to highlight “Confirmation”.
– Use right page to select to display sub-menu as to what to confirm.
– Select “Full Service” (No need to use -+.) to confirm this choice
– Press right page to confirm. (Delay is about 3 seconds.)
– Press left page twice to exit the menu system, or turn off the ignition switch.
– Turn off ignition. Turn back on. The display should show that it is recalculating the mileage and days. This takes about 60 seconds so be patient.
Metod 2
1. Put the key in the ignition and switch it on without starting the engine.
(Wait for LCD to return to the vehicle mileage)
2. Hold the “O” button down till you hear a beep (could take a while, 30 sec.)
3. Press the M button repeatedly and a number of reset menus will appear, (If you have used oil according to quality sheet 229.31 or 228/229.51 you can scroll to Reset.31 or Reset.51 respectively.) Select “reset 51”
4. Now, when appropriate oil type is selected press “O” for 6 seconds until ”2” is displayed.
5. Press “O” once again briefly and the ” reset done” message will confirm that the job is done.
6. Pull the Key out
FOR THE 2004 DODGE SPRINTER!
Turn the key to position 2 in the ignition lock and immediately press the button MI (km) twice.
Within 10 seconds, return the key to the 0 in the ignition lock.
Press and hold the button MI (km). Turn the key to position 2 in the ignition lock. Keep the button MI (km) pressed.
The maintenance indicator with the time/distance is shown.
After about 10 seconds, an acoustic signal will sound and the maintenance indicator is displayed with the new remaining time / distance .
Release the button MI (km)