Reset service light indicator Renault Megane 2. From year: 2002, 2003, 2004, 2005, 2006, 2007, 2008.
How to reset service light indicator Renault Megane 2.
To reset Service Due Now on a Renault Megane 2, follow these steps:
1. Switch ON the gnition, don’t start the vehicle. For cars with keycard ignition, insert the card, then push & hold the start button for 5 seconds to turn on the dashboard cluster.
2. Push and release the button on the end of the wiper stalk until the Service Due Now message appears on the display. Some models have 2 buttons, which cycle through the options in opposite directions, either button can be used in this case.
3. When Service Due Now message is displayed push and hold the same button located at the end of wiper stalk.
4. Now the Service Due now will start to flash after that the display will change to the new service interval and still flashing.
5. Keep holding the button until the display stops flashing.
6. Done, have managed to reset service light indicator Renault Megane 2.
2009-2011
1. Push the ignition switch to the ON position (do not start the engine). Use the ENTER button (?) and toggle the vehicle information display to show the SETTING screen. Use the NEXT button (?) to select.
2. Use the NEXT button (?) to select MAINTENANCE
i) SETTING > MAINTENANCE > OIL > ENGINE OIL to set or reset the mileage for the engine oil change.
ii) SETTING > MAINTENANCE > FILTER > to set or reset the mileage for the engine oil filter.
3. Turn the ignition off and then start the engine to verify the indicator has been reset.
1998-1999
*Diagnostic Reset Tool Required
Manual Reset:
1. Turn key in steering lock to position 2.
2. Within 4 seconds press button (1) left of speedometer twice.
3. The present status for days or distance displays
4. Press and hold button (1)
5. Continue to hold button (1) for approximately 10 seconds until a signal sounds and the display shows 10 000 mils or 15 000km. Release button (1).
6. Turn the ignition off and then start the engine to verify the indicator has been reset.
2000-2001
*Diagnostic Reset Tool Required
Manual Reset:
1. Switch ignition on and immediately press knob to left of speedometer twice within 4 seconds.
2. Present status for days or distance is now displayed. Within 10 seconds
3. Press and hold button to the left of speedometer
4. Release button.
5. Service interval displays the reset interval.
6. Turn the ignition off and then start the engine to verify the indicator has been reset.
2002-2004
1. Switch ignition on and immediately press knob to left of speedometer twice within 1 second.
2. Present status for days or distance is now displayed. Within 10 seconds
3. Press and hold button to the left of speedometer
4. Release button.
5. Service interval displays the reset interval.
6. Turn the ignition off and then start the engine to verify the indicator has been reset.
2005-2009
1. Turn the ignition to position 1.
2. Press the system selection button (3 located on the lower left of the steering wheel) repeatedly until the kilometer reading is shown in the multi information display.)
3. Press the cluster illumination button (lower left of instrument panel) quickly 3 times. The battery voltage will be displayed.
4. Press the up or down buttons until the service menu appears.
5. Use the +/- buttons to select menu oprion “”CONFIRM””.”
6. Press the system selection button uuntil “”COMPLETE SERVICE”” is selected.”
7. Confirm “”Complete Service”” with system selection button. The display will show “”SERVICE CONFIRMED””.”
8. Turn the ignition off and then start the engine to verify the indicator has been reset.
2010-2012
1. Turn the ignition to position 1. (close all doors
2. Press the scroll forward button (bottom button on left side of steering wheel controls) to display mileage counter.
3. Press the system selection button (left button on left side of steering wheel controls) repeatedly until the menu item “”trip”” with highlighter is displayed. “”Trip”” remains selected for 5 seconds so move quickly to step 4.”
4. Press and hold accept/end phone button and within 1 second press and hold the button in the center of the arrows (left side of steering wheel). In 5 seconds the Workshop menu will be displayed “”Vehicle data
5. Use scroll forward or backward to highlight “”ASSYST PLUS”” and confirm selection using the button in the center of the arrows. “”Service data”” and “”Full service”” appear in the display.”
6. Use scroll forward or backward to select “”Full service”” and confirm selection with the button in the center of the arrows. The display will show “”Service 1
7. Use scroll forward or backward to select “”Confirm serv”” and confirm selection with the button in the center of the arrows.”
8. Use scroll forward or backward to select engine oil specification used. “”Oil qual. 229.3″” and “”Oil qual. 229.5″” are displayed. Confirm selection with center button. The display shows “”Serv conducted?”””
9. Use scroll forward or backward to select “”Yes”” and confirm with center button. Display will show “”Take-back not possible
10. Use scroll forward or backward until “”Configuration”” is highlighted and confirm selection with button in center of the arrows. “”Full service carried out”” appears in the display.”
11. Use scroll forward and backward to exit menu.
12. Turn the ignition off and then start the engine to verify the indicator has been reset.
2006-2012
1. Turn ignition to Terminal 15 which is one turn of the key or one press of the START/STOP button.
2. Press and hold the trip odometer reset button for approximately 10 seconds until the first service job appears in the display.
3. The upper display in the Instrument Cluster will be illuminated with a Service Item (example: An oil can is the designation for Oil Service). The lower display in the Instrument Cluster will indicate the remaining time or mileage left for that Service Item (example: 14000). Press the on-board computer button repeatedly (located on the direction indicator/main-beam switch) to scroll through all of the Condition Based Service Items.
4. Press and hold the on-board computer button on the direction indicator/main-beam switch until “”RESET”” appears in the lower display.”
5. Pressing the on-board computer button again resets the service shown in the upper display. Repeat the procedure for each additional service which is to be reset.
6. Turn the ignition off and start the engine to verify the indicator has been reset.
1988-2001
BMW recommends the use of a reset tool.
2002-2005
1. Turn ignition on but do not start engine.
2. Press the RESET button on the top left side of the instrument cluster for 10 seconds to display a four (4) line menu in the speedometer.
3. Press the RESET button or LOWER AXIAL (FAS) button on the turn signal/high beam switch to scroll through the menu.
4. Select ENGINE OIL and press the RESET button for a few seconds to display a two (2) line menu in the tachometer.
5. Press the RESET (or AXIAL) button to select the SERVICE AND MAINTENANCE.
6. Press the RESET button again for a few seconds.
7. Turn the ignition off and start the engine to verify the indicator has been reset.
2006-2012
BMW recommends the use of a reset tool.
Manual Reset
1. Turn ignition to Terminal 15 which is one turn of the key or one press of the START/STOP button.
2. Press and hold the Instrument Cluster Set/Reset button for 10 seconds.
3. The upper display in the Instrument Cluster will be illuminated with a Service Item. The lower display in the Instrument Cluster will indicate the remaining time or mileage left for that Service Item. Pressing the button repeatedly will allow the display to scroll through all of the Condition Based Service Items.
4. Press and hold the Instrument Cluster Set/Reset button again and the lower display screen will indicate “”OK”” or “”DUE””.”
5. Pressing the Instrument Cluster Set/Reset button again will allow the “”RESET”” to appear in the lower window for that service. Releasing and reapplying the button one more time will reset the service displayed in the upper window only. ”
6. Turn the ignition off and start the engine to verify the indicator has been reset.