Here’s how to do it yourself in no time works on a few different Jags….
Service Light Reset Instructions:
1 . Insert key into ignition.
2 . Press and hold the Reset switch (located on the Trip Computer Switchpack ).
3 . NOTE: The reset switch has to be released immediately after the ignition is switched ‘ON’. This is critical to enable the rest of the procedure.
Turn the key to Ignition position II and at the point of entering Ignition position II (i.e when a click is heard), instantaneously release the Reset switch.
4 . Wait one second.
5 . Press and hold the Trip switch (located on the end of the left-hand side stalk).
6 . Wait one second.
7 . Press and hold the Reset switch (whilst still holding the Trip switch).
8 . The cluster should display (within three seconds) the warning message ‘RESETTING SERVICE MODE’.
9 . Keep both buttons pressed until the warning message changes to ‘SERVICE MODE RESET’ (after ten seconds).
10 . Once the message is displayed the buttons may be released — sequence is now complete.
11 . If a Service Required message was displayed prior to the reset sequence, cycle the ignition to ‘Off’ and then back to Ignition position II and check that the message is no longer displayed.
2005-2009
Manual Reset Procedure:
Press and hold the trip reset button.
Turn the ignition switch on to the ignition position II (one position before starting engine).
If the SII (Service Indicator Interval) function is enabled the information display will flash ‘SERVICE’ for 5 seconds and then display ‘SERVICE’ constantly. If the SII function is not enabled the information display will show the normal odometer and trip information.
If the trip reset button is released within 10 seconds of entering the reset mode, the information display will show ‘DIST’. If the trip reset button is not released after 10 seconds the instrument cluster will exit the manual reset procedure.
If the oil service value is to be reset, press the trip reset button within 10 seconds for 5 seconds and then reset the oil service value, the display will then show ‘END’.
If the trip reset button is pressed for 5 seconds the display will exit the reset routine. If the trip reset button is not pressed for more than 10 seconds, then the information display will exit the reset routine. Turn the ignition off and then start the engine to verify the indicator has been reset.
2005-2009
Turn the ignition to run (one position before starting engine).
Use the fuel button on the Driver Information Center to reach the ENGINE OIL LIFE screen.
Press and hold the select button on the DIC for 5 seconds while ENGINE OIL LIFE is displayed.
OIL LIFE RESET will appear on the DIC display for 10 seconds to let you know the system is reset. If the change oil light comes back on when you start your vehicle, the engine oil life system has not reset, repeat the procedure.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2004-2006
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the ODO/TRIP knob then the turn ignition off.
Hold down the ODO/TRIP knob while turning the ignition key to the run position (one position before starting engine).
Hold down the button for 5 seconds or more. The odometer indicates “000000” and the light goes off.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2007-2009
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the trip meter reset knob then the turn ignition off.
Hold down the trip meter reset knob while turning the ignition key to the run position (one position before starting engine).
Hold down the button for 5 seconds or more. The odometer indicates “000000” and the light goes off.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2010
Turn the ignition to run (push START/STOP button once). Use the trip meter switch to bring up the trip meter A reading. Turn the ignition off.
While pressing the ěODO/TRIPî button, set the engine switch to run (push START/STOP button once).
Continue holding the “ODO/TRIP button for about 5 seconds. The resetting procedure is complete when “000000” in the trip metre flashes once and the message in the multi information display disappears.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2004-2007
Turn the ignition to run (one position before starting engine).
Push the ěTRIPî button repeatedly to display “MAINTENANCE” and press the “ENTER” button.
Select “Engine Oil” and press the “ENTER” button.
Select “RESET” and press “ENTER” button.
Press “PREV” to return to previous menu.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2008-2010
Turn the ignition on without starting the engine (press START/STOP) button.
Push the ěINFOî button on the control panel for the Vehicle Information screen.
Use arrow keys to scroll down to “Maintenance” and press “ENTER” button to select.
Select “Reminder 1” and press “ENTER” button.
Select “Reset Distance” and press “ENTER” button.
Press “Back” button to return to “Maintenance” menu and repeat procedure for “Reminder 2″… Turn the ignition off and then start the engine to verify the indicator has been reset.