2005-2009
Manual Reset Procedure:
Press and hold the trip reset button.
Turn the ignition switch on to the ignition position II (one position before starting engine).
If the SII (Service Indicator Interval) function is enabled the information display will flash ‘SERVICE’ for 5 seconds and then display ‘SERVICE’ constantly. If the SII function is not enabled the information display will show the normal odometer and trip information.
If the trip reset button is released within 10 seconds of entering the reset mode, the information display will show ‘DIST’. If the trip reset button is not released after 10 seconds the instrument cluster will exit the manual reset procedure.
If the oil service value is to be reset, press the trip reset button within 10 seconds for 5 seconds and then reset the oil service value, the display will then show ‘END’.
If the trip reset button is pressed for 5 seconds the display will exit the reset routine. If the trip reset button is not pressed for more than 10 seconds, then the information display will exit the reset routine. Turn the ignition off and then start the engine to verify the indicator has been reset.
1997-1999
*Diagnostic Reset Tool Required
Turn key in steering lock to position 2.
Within 4 seconds press button (1) left of speedometer twice.
The present status for days or distance displays, within 10 seconds turn key in steering lock to position 0.
Press and hold button (1), while turning key in steering lock to position 2 again. The present status for days or distance displays once more.
Continue to hold button (1) for approximately 10 seconds until a signal sounds and the display shows 10 000 mils or 15 000km. Release button (1).
2000-2004
Turn on the ignition (standard display of the control system appears).
Press button (UP arrow) or (DOWN arrow) on the multifunction steering wheel until the FSS indicator with (Single Wrench) or (Double Wrench) and the service deadline appears in the multifunction display.
Press the reset knob to the right in the instrument cluster for about 2 seconds. This message appears in the multifunction display: “SERVICE INTERVAL? RESET WITH R BUTTON”.
To confirm hold down the reset button until you hear a signal. The service indicator now displays the reset interval.
2002
Turn key in steering lock to position 2.
Press either of the lower two system select buttons on left hand side of steering wheel (looks like 2 over lapping file folders) until the trip and main odometer display appears.
Press either of the top buttons on steering wheel (arrows) until the FSS indicator appears.
Press R button on the instrument cluster for 2-4 seconds.
The display reads “DO YOU WANT TO RESET SERVICE INTERVAL? CONFIRM BY PRESSING R”.
Press R button on the instrument cluster again and hold until signal sounds (about 10 seconds). Message now reads “SERVICE INTERVAL HAS BEEN RESET”.
2003
Turn on the ignition (standard display of the control system appears).
Press button (UP arrow) or (DOWN arrow) on the multifunction steering wheel until the FSS indicator appears in the multifunction display.
Press the reset knob for about 4 seconds. The message appears in the tachometer “DO YOU WANT TO RESET SERVICE INTERVAL? CONFIRM BY PRESSING R”.
To confirm, hold down the reset knob until you hear a signal. The service indicator now displays the reset interval.
2004
Turn on the ignition (standard display of the control system appears).
Press button (UP arrow) or (DOWN arrow) on the multifunction steering wheel until the FSS indicator appears in the multifunction display.
Press the reset knob for about 3 seconds. The message appears in the tachometer “SERVICE INTERVAL? RESET WITH R BUTTON FOR 3 SEC.”.
To confirm, hold down the reset knob until you hear a signal. The service indicator now displays the reset interval.
1997-2000
*Diagnostic Reset Tool Required (please refer to TOOLS page)
Manual Reset:
Turn key in steering lock to position 2.
Within 4 seconds press 0 button twice.
The present status for days or distance displays, within 10 seconds turn the electroninc key in steering lock to position 0.
Press and hold 0 button while turning electronic key in steering loack to position 2 again. The present status for days or distance displays once more. Continue to hold 0 button for approximately 10 seconds until a signal sounds and the display shows 10 000 (15000KM) for approximately 10 seconds.
Release 0 button, the status is reset.
2001-2002
*Diagnostic Reset Tool Required (please refer to TOOLS page)
Manual Reset:
Turn key in steering lock to position 2.
To call up the trip odometer and main odometer, press either of lower two buttons on left hand side of steering wheel (system select – looks like file folder) until the display appears.
Press either of the top buttons on steering wheel (arrows) until the FSS indicator appears.
Press R button on the instrument cluster for 2-4 seconds.
The display reads “DO YOU WANT TO RESET SERVICE INTERVAL? CONFIRM BY PRESSING R”
Press R button on the instrument cluster again and hold until signal sounds. The message “SERVICE INTERVAL HAS BEEN RESET” appears in the multifunction display.
2003-2004
Turn on the ignition (standard display of the control system appears).
Press button (UP arrow) or (DOWN arrow) on the multifunction steering wheel until the FSS indicator appears in the display.
Press the reset knob for about 5 seconds until the SERVICE MENU appears in the multifunction display.
Select the CONFIRMATION menu with the (+) or (-) button.
Press the menu button (looks like file 2 over lapping file folders).
The service indicator now displays the CONFIRMATION menu. The selection marker is on CONFIRM. Press the menu button (looks like 2 over lapping file folders). The service indicator now displays the CONFIRM menu. The selection marker is on STANDARD OIL.
Press the menu button (looks like 2 over lapping file folders). The words SERVICE CONFIRMED appear in the multifunction display. The service indicator is now reset.
Press the menu button on the multifunction steering wheel until the standard display appears in the multifunction display.
1997-1999
*Diagnostic Reset Tool Required (please refer to TOOLS page)
Manual Reset:
Turn key in steering lock to position 2.
Within 4 seconds press 0 button twice.
The present status for days or distance displays, within 10 seconds turn the electroninc key in steering lock to position 0.
Press and hold 0 button while turning electronic key in steering loack to position 2 again. The present status for days or distance displays once more. Continue to hold 0 button for approximately 10 seconds until a signal sounds and the display shows 10 000 (15000KM) for approximately 10 seconds.
Release 0 button, the status is reset.
2000-2003
Turn on the ignition (standard display of the control system appears).
Press button (UP arrow) or (DOWN arrow) on the multifunction steering wheel until the FSS indicator with (Single Wrench) or (Double Wrench) and the service deadline appears in the multifunction display.
Press the reset knob to the left in the instrument cluster for about 4 seconds. This message appears in the multifunction display: “DO YOU WANT TO RESET SERVICE INTERVAL? TO CONFIRM PRESS BUTTON”.
To confirm hold down the reset button until you hear a signal. The service indicator now displays the reset interval.
2004
Turn on the ignition (standard display of the control system appears).
Press button (UP arrow) or (DOWN arrow) on the multifunction steering wheel until the FSS indicator with (Single Wrench) or (Double Wrench) and the service deadline appears in the multifunction display.
Press the reset knob to the left in the instrument cluster for about 4 seconds. This message appears in the multifunction display: “SERVICE INTERVAL…TO RESET: PRESS RESET BUTTON FOR 3 SECONDS”.
To confirm hold down the reset button until you hear a signal. The service indicator now displays the reset interval.