2009-2010
Turn the ignition to run (one position before starting engine).
Press and release the SELECT/RESET stem to display “OIL LIFE = XXX% HOLD RESET = NEW”.
Press and hold the SELECT/RESET stem for 2 seconds and release. Oil life is set to XX% and “OIL LIFE SET TO XX%” is displayed.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2005-2009
Manual Reset Procedure:
Press and hold the trip reset button.
Turn the ignition switch on to the ignition position II (one position before starting engine).
If the SII (Service Indicator Interval) function is enabled the information display will flash ‘SERVICE’ for 5 seconds and then display ‘SERVICE’ constantly. If the SII function is not enabled the information display will show the normal odometer and trip information.
If the trip reset button is released within 10 seconds of entering the reset mode, the information display will show ‘DIST’. If the trip reset button is not released after 10 seconds the instrument cluster will exit the manual reset procedure.
If the oil service value is to be reset, press the trip reset button within 10 seconds for 5 seconds and then reset the oil service value, the display will then show ‘END’.
If the trip reset button is pressed for 5 seconds the display will exit the reset routine. If the trip reset button is not pressed for more than 10 seconds, then the information display will exit the reset routine. Turn the ignition off and then start the engine to verify the indicator has been reset.
2006-2010
Press and hold the trip reset button with the vehicle stationary and in a power mode less than 6 (two positions before starting engine).
While holding the trip reset button, enter the vehicle into power mode 6 (one position before starting engine).
Release the trip reset button within 10 seconds of entering power mode If the manual reset mode has been successfully entered ‘dISt’ or ‘DATE’ will be displayed in the odometer, depending on which trigger has been activated.
To clear the ‘dISt’ trigger press, and hold the trip reset button for more than 5 seconds within 10 seconds of entering the manual re-set mode. If successful, ‘RESET’ will be displayed in the odometer for 5 seconds. If the date trigger has not been activated ‘END’ will then be displayed in the odometer.
If the date trigger has been activated, ‘DATE’ will be displayed in the odometer. To clear the trigger press and hold the trip reset button for more than 5 seconds within 10 seconds of ‘DATE’ being displayed. If successful, ‘RESET’ will be displayed within the odometer for 5 seconds followed by ‘END’ The odometer will now exit re-set mode.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2002-2006
*Diagnostic Reset Tool Required (please refer to TOOLS page)
2007-2010
*Diagnostic Reset Tool Required (please refer to TOOLS page)
Manual Reset:
Turn ignition to Terminal 15 which is one turn of the key or one press of the START/STOP button.
Press and hold the trip odometer reset button for approximately 10 seconds until the first service job appears in the display.
The upper display in the Instrument Cluster will be illuminated with a Service Item (example: An oil can is the designation for Oil Service). The lower display in the Instrument Cluster will indicate the remaining time or mileage left for that Service Item (example: 14000). Press the on-board computer button repeatedly (located on the direction indicator/main-beam switch) to scroll through all of the Condition Based Service Items.
Press and hold the on-board computer button on the direction indicator/main-beam switch until “RESET” appears in the lower display.
Pressing the on-board computer button again resets the service shown in the upper display. Repeat the procedure for each additional service which is to be reset.
Turn the ignition off and start the engine to verify the indicator has been reset.
For oil press and hold the right hand button on the cluster – oil will appear in the display – release right hand button then turn left hand button clockwise until —– appears.
For insp prees and hold right hand button – turn on ignition – release button then press and release button again – insp will appear in the display – turn left hand button as before until —– appears.
note: if you’re clearing the insp service sometimes it’s neccessary to clear the oil service afterwards (if it wasn’t done at oil service)