1. Turn the ignition key to ON but do not start the engine.
2. Slowly depress the accelerator to the floor and release it three times within 10 seconds.
3. Turn the ignition key to the OFF position.
The service light on these vehicles is usually a spanner / wrench symbol. To reset that indicator:
Turn the Ignition ON (position 2) but do not start the engine
(On cars with keycard ignition, insert the card, then press and hold the start button for 5 seconds to turn on the dash cluster)
Press the button on the end of the wiper stalk repeatedly until the spanner symbol and miles to service appears on the display
(Some models have 2 buttons, which cycle through the options in opposite directions – either button can be used in this case)
Press and hold the button
The display will now change to the new service interval and start flashing
Keep holding the button until the display stops flashing
Release the button
Skoda 2000
Longlife service intervals require diagnostic tool. Fixed intervals: Press and hold button below the speedometer. Turn ignition to the “ON” position.
“SERVICE” is displayed. Release button. Turn button below the tachometer to the right until display is reset. Turn ignition off.
Toyota 4Runner 2003-onwards
With the ignition “OFF”, press and hold “RESET” button. Turn ignition to the “ON” position. Continue to hold button until “MAINT REQD” light turns off.
Turn ignition off.
Camry 2004-onwards
With the ignition “OFF”, press and hold button below the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Corolla
Turn the key to the off position. Press and hold down the trip meter button and turn the key to the “on” position. Continue to hold the trip button for 5 seconds after the key is turned on, then release.
Highlander 2004-onwards
With the ignition “OFF”, press and hold button below the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Matrix 2004-onwards
With the ignition “OFF”, press and hold button below the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Prius 2004-onwards
With the “POWER” switch off, press and hold “ODO TRIP” button. Press “POWER” switch twice selecting “IG-ON”. Continue to hold button until”000000″ is displayed and “MAINT REQD” light turns off. Turn “POWER” switch to off.
RAV4 2004-onwards
With the ignition “OFF”, press and hold button below the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Sequoia 2004-onwards
With the ignition “OFF”, press and hold button below the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Sienna 2004-onwards
With the ignition “OFF”, press and hold button to the right of the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″
is displayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Solara 2004-onwards
With the ignition “OFF”, press and hold button to the left of the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Tacoma 2005-onwards
With the ignition “OFF”, press and hold button to the right of the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″
is displayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Tundra 2003-onwards
With the ignition “OFF”, press and hold button below the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Turn the car on. Wait about a minute for the computer to get to normal.
press and hold the travel mile reset button. Hold it untill an ! in a triangle appears. then your maintanance info will pop up. select the item to reset. and tap the side button on the wand atached to the stearing wheel. this button is what you use to browse through your computer. press the button once it will say “reset” press and hold it the second time and it will say reset, hold for 5 seconds or so and it will show a check mark next to “reset” confirming it has reset.