Service Reset:
1)Push-hold Trip Button (TB)
2)Turn key to position 1
3)Continue to hold (TB), the number 15A will show to the teft of the milage
4)Release (TB) for 3 sec and then hold (TB) again
5)In about 5-8 sec RST will show in the left corner
6)Release and then hold again 15000 will show, press and release
7)Car is now reset to the 15,000 service – (has completed 10,000 mile service) and will count down from 15,000.
2000
Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds. The reset is complete when the CHANGE OIL SOON indicator flashes 2 times.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2001-2004
Turn the ignition to run (one position before starting engine).
Repeatedly push the TRIP/RESET button until OIL is displayed on the Driver Information Centre.
Push and hold the RESET button for 5 seconds. The number will disappear and be replaced by 100%.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2005-2007
Turn the ignition to run (one position before starting engine).
Push the set/reset button until OIL is displayed on the DIC.
Once OIL is displayed, push and hold the set/reset button for 5 seconds. The number will disappear and be replaced by 100 (indicating 100% oil life remaining).
Turn the ignition off and then start the engine to verify the indicator has been reset.
2000
Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds. If the CHANGE OIL SOON indicator flashes 2 times, the system is reset.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2001-2005
Turn the ignition to run (one position before starting engine).
Repeatedly push the TRIP/RESET button until OIL is displayed on the DIC.
Push and hold the TRIP/RESET button for 5 seconds. The number will disappear and be replaced by
100 indicating 100 percent oil life remaining.
Turn the ignition off and then start the engine to verify the indicator has been reset.
How to reset the Maintenance Service interval:
Metod 1
– Switch ignition on to position one, (first click clockwise);
– “Outside temperature” should be displayed, if not move to it (You have to be in this display to go further);
– Press the trip odometer, “reset”, knob three times consecutively ( The Voltage display will appear);
– Press Down Arrow to enter the “Service Menu”. “Service Data” submenu below will be highlighted.
– Press right page to enter the Service data submenu. (Left page goes up in menus, -+ selects items displayed)
– Press – three times on right of wheel to highlight “Confirmation”.
– Use right page to select to display sub-menu as to what to confirm.
– Select “Full Service” (No need to use -+.) to confirm this choice
– Press right page to confirm. (Delay is about 3 seconds.)
– Press left page twice to exit the menu system, or turn off the ignition switch.
– Turn off ignition. Turn back on. The display should show that it is recalculating the mileage and days. This takes about 60 seconds so be patient.
Metod 2
1. Put the key in the ignition and switch it on without starting the engine.
(Wait for LCD to return to the vehicle mileage)
2. Hold the “O” button down till you hear a beep (could take a while, 30 sec.)
3. Press the M button repeatedly and a number of reset menus will appear, (If you have used oil according to quality sheet 229.31 or 228/229.51 you can scroll to Reset.31 or Reset.51 respectively.) Select “reset 51”
4. Now, when appropriate oil type is selected press “O” for 6 seconds until ”2” is displayed.
5. Press “O” once again briefly and the ” reset done” message will confirm that the job is done.
6. Pull the Key out
FOR THE 2004 DODGE SPRINTER!
Turn the key to position 2 in the ignition lock and immediately press the button MI (km) twice.
Within 10 seconds, return the key to the 0 in the ignition lock.
Press and hold the button MI (km). Turn the key to position 2 in the ignition lock. Keep the button MI (km) pressed.
The maintenance indicator with the time/distance is shown.
After about 10 seconds, an acoustic signal will sound and the maintenance indicator is displayed with the new remaining time / distance .
Release the button MI (km)