2007-2011
1. Turn the ignition to run (one position before starting engine).
2. Select trip metre A reading by using the trip metre button and then turn the ignition off.
3. While pressing the trip meter reset button
4. Continue to press and hold the button until the trip meter displays “”000000″”.”
5. Turn the ignition off and then start the engine to verify the indicator has been reset.
2012
1. Turn the ignition to run (one position before starting engine).
2. Press the MODE switch knob on the upper right side of the combination meter until “”TRIP A”” is shown and then turn the ignition off.”
3. While pressing the trip meter reset button
4. After the reset procedure is complete
5. Turn the ignition off and then start the engine to verify the indicator has been reset.
Reset oil service light Ford Explorer Sport Trac. From years: 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010.
How do you reset oil service light Ford Explorer Sport Trac. From years:1999, 2000, 2001.
How to reset oil service light Ford Explorer Sport Trac. From years: 2002, 2003.
Full procedure how to reset oil service light Ford Explorer Sport Trac. From years: 2004, 2005.
How can you reset oil service light Ford Explorer Sport Trac. From years: 2006, 2007.
To reset the oil monitoring system to 100% after each oil change Ford Explorer Sport Trac. From years: 2006, 2007 [approximately 5,000 miles (8,000 km) or 180 days] perform the following.
Note: To change oil life 100% miles value from 5,000 miles (8,000 km) or 180 days to another value, refer to the Oil Life Start Value selected from the SETUP MENU in this section.
Reset Oil life Start Value Ford Explorer Sport Trac. From years: 2006, 2007.
Note: Oil Life Start Value of 100% equals 5,000 miles (8,000 km) or 180 days. For example, setting Oil Life Start Value to 60% sets the Oil Life Start Value to 3,000 miles (4,828 km) and 120 days.
How do you reset oil service light Ford Explorer Sport Trac. From years:2008, 2009, 2010.
To reset the oil monitoring system to 100% after each oil change Ford Explorer Sport Trac. From years: 2008, 2009, 2010 [approximately 7,500 miles (12,070 km) or 6 months] perform the following.
OIL CHANGE REQUIRED. Displayed when the engine oil life remaining is 0%.
An oil change is required whenever indicated by the message center and according to the recommended maintenance schedule.
ENGINE OIL CHANGE SOON. Displayed when the engine oil life reaches 5% or less of the Oil Life Start Value.
1998
Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds. If the CHANGE OIL indicator flashes, the system is resetting.
Turn the ignition off and then start the engine to verify the indicator has been reset.
1999
Without Driver Information Centre:
Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds. If the CHANGE OIL SOON indicator flashes 2 times, the system is resetting.
Turn the ignition off and then start the engine to verify the indicator has been reset.
With Driver Information Centre:
Turn the ignition to run (one position before starting engine).
To reset the oil life monitor, press and hold the MODE button until the light appears next to Oil Life.
Press and hold the trip RESET button unitl the oil life % changes to 99%.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2000-2002
Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds. If the CHANGE ENG OIL light flashes, the system is resetting.
Turn the ignition off and then start the engine to verify the indicator has been reset.
1994-1995
Engine Oil Life Monitor
Turn the ignition to run (one position before starting engine).
Display the oil life index on the Driver Information System.
Hold the RESET button for 5 seconds. When a DIC message of RESET is displayed and the oil life index equals 100%, the reset is complete.
Turn the ignition off and then start the engine to verify the indicator has been reset.
Change Oil Soon
Turn the ignition to run (one position before starting engine).
Press OIL button and release.
Select OIL menu by pressing MODE button.
Press and hold the RESET button for 5 to 7 seconds.
Turn the ignition off and then start the engine to verify the indicator has been reset.
1996-1997
Turn the ignition to run (one position before starting engine).
Display the oil life index on the Driver Information System.
Hold the RESET button for 5 seconds.
Turn the ignition off and then start the engine to verify the indicator has been reset.
1998
Turn the ignition to run (one position before starting engine).
Press the TRIP button on the Driver Information System (DIC) switch to view various menu choices and stop on OIL LIFE REMAINING.
Press and hold the RESET button on the DIC switch for more than 5 seconds. The oil life will change to 100%. The engine oil life monitor is now reset.
Turn the ignition off and then start the engine to verify the indicator has been reset.
1999
Turn the ignition to run (one position before starting engine).
Press and hold the OIL RESET button in the IP storage compartment for at least 5 seconds, but no more than 60 seconds.
After 5 seconds, observe the CHANGE OIL SOON light flash 4 times before light turns off. This indicates that the engine oil life monitor system has reset.
Turn the ignition off and then start the engine to verify the indicator has been reset.
Here’s how to do it yourself in no time works on a few different Jags….
Service Light Reset Instructions:
1 . Insert key into ignition.
2 . Press and hold the Reset switch (located on the Trip Computer Switchpack ).
3 . NOTE: The reset switch has to be released immediately after the ignition is switched ‘ON’. This is critical to enable the rest of the procedure.
Turn the key to Ignition position II and at the point of entering Ignition position II (i.e when a click is heard), instantaneously release the Reset switch.
4 . Wait one second.
5 . Press and hold the Trip switch (located on the end of the left-hand side stalk).
6 . Wait one second.
7 . Press and hold the Reset switch (whilst still holding the Trip switch).
8 . The cluster should display (within three seconds) the warning message ‘RESETTING SERVICE MODE’.
9 . Keep both buttons pressed until the warning message changes to ‘SERVICE MODE RESET’ (after ten seconds).
10 . Once the message is displayed the buttons may be released — sequence is now complete.
11 . If a Service Required message was displayed prior to the reset sequence, cycle the ignition to ‘Off’ and then back to Ignition position II and check that the message is no longer displayed.