1998-1999
*Diagnostic Reset Tool Required
Manual Reset:
1. Turn key in steering lock to position 2.
2. Within 4 seconds press button (1) left of speedometer twice.
3. The present status for days or distance displays
4. Press and hold button (1)
5. Continue to hold button (1) for approximately 10 seconds until a signal sounds and the display shows 10 000 mils or 15 000km. Release button (1).
6. Turn the ignition off and then start the engine to verify the indicator has been reset.
2000-2001
*Diagnostic Reset Tool Required
Manual Reset:
1. Switch ignition on and immediately press knob to left of speedometer twice within 4 seconds.
2. Present status for days or distance is now displayed. Within 10 seconds
3. Press and hold button to the left of speedometer
4. Release button.
5. Service interval displays the reset interval.
6. Turn the ignition off and then start the engine to verify the indicator has been reset.
2002-2004
1. Switch ignition on and immediately press knob to left of speedometer twice within 1 second.
2. Present status for days or distance is now displayed. Within 10 seconds
3. Press and hold button to the left of speedometer
4. Release button.
5. Service interval displays the reset interval.
6. Turn the ignition off and then start the engine to verify the indicator has been reset.
2005-2009
1. Turn the ignition to position 1.
2. Press the system selection button (3 located on the lower left of the steering wheel) repeatedly until the kilometer reading is shown in the multi information display.)
3. Press the cluster illumination button (lower left of instrument panel) quickly 3 times. The battery voltage will be displayed.
4. Press the up or down buttons until the service menu appears.
5. Use the +/- buttons to select menu oprion “”CONFIRM””.”
6. Press the system selection button uuntil “”COMPLETE SERVICE”” is selected.”
7. Confirm “”Complete Service”” with system selection button. The display will show “”SERVICE CONFIRMED””.”
8. Turn the ignition off and then start the engine to verify the indicator has been reset.
2010-2012
1. Turn the ignition to position 1. (close all doors
2. Press the scroll forward button (bottom button on left side of steering wheel controls) to display mileage counter.
3. Press the system selection button (left button on left side of steering wheel controls) repeatedly until the menu item “”trip”” with highlighter is displayed. “”Trip”” remains selected for 5 seconds so move quickly to step 4.”
4. Press and hold accept/end phone button and within 1 second press and hold the button in the center of the arrows (left side of steering wheel). In 5 seconds the Workshop menu will be displayed “”Vehicle data
5. Use scroll forward or backward to highlight “”ASSYST PLUS”” and confirm selection using the button in the center of the arrows. “”Service data”” and “”Full service”” appear in the display.”
6. Use scroll forward or backward to select “”Full service”” and confirm selection with the button in the center of the arrows. The display will show “”Service 1
7. Use scroll forward or backward to select “”Confirm serv”” and confirm selection with the button in the center of the arrows.”
8. Use scroll forward or backward to select engine oil specification used. “”Oil qual. 229.3″” and “”Oil qual. 229.5″” are displayed. Confirm selection with center button. The display shows “”Serv conducted?”””
9. Use scroll forward or backward to select “”Yes”” and confirm with center button. Display will show “”Take-back not possible
10. Use scroll forward or backward until “”Configuration”” is highlighted and confirm selection with button in center of the arrows. “”Full service carried out”” appears in the display.”
11. Use scroll forward and backward to exit menu.
12. Turn the ignition off and then start the engine to verify the indicator has been reset.
2000-2004
*Diagnostic Reset Tool Required
Manual Reset using DIS and Reset Knobs:
1. Turn off the ignition
2. Locate the Driver Information System (DIS) in the instrument panel.
3. Do the following to display the SERVICE! message in the display.
i) Press and hold the right RESET knob.
ii) Turn on the ignition – do not start the engine.
iii) Release the knob.
4. Do the following to display the next service interval (SERVICE IN ##MI)
i) Press and hold the right RESET knob.
ii) Release the knob.
5. Turn off the ignition.
6. Start the engine and verify indicator has been reset.
Manual Reset for 2000 only:
1. Turn off the ignition.
2. Press and hold the TRIP RECORDER reset button on the instrument cluster and turn on the ignition.
3. Release the button. The display will show SERVICE IN —MI or SERVICE.
4. Within 5 seconds
5. Turn off the ignition.
6. Start the engine and verify indicator has been reset.
2005-2007
1. Turn off the ignition.
2. Press and hold the button to the right of the LCD display in the instrument cluster.
3.Turn the ignition on (do not start the engine); the message “”SERVICE”” appears. Release button.”
4. Within 5 seconds
5. Turn off the ignition.
6. Start the engine and verify indicator has been reset.
2008-2012
“Audi recommends the use of a reset tool. *Depening on model
2001-2005
Manual Reset using DIS and Reset Knobs:
1. Turn off the ignition
2. Locate the Driver Information System (DIS) in the instrument panel.
3. Locate the reset buttons (WRENCH button and 0
4. Do the following to display the SERVICE! Message in the DIS:
i) Press and hold the Wrench button.
ii) Turn on the ignition – do not start the engine.
iii) Release the WRENCH button.
5. Do the following to display the next service interval (SERVICE in ##MI)
i) Press and hold the 0
ii) Release the 0
6. Turn off the ignition.
7. Start the engine and verify indicator has been reset.
Manual Reset using DIS and Reset Knobs:
1. Turn off the ignition
2. Locate the Driver Information System (DIS) in the instrument panel.
3. Do the following to display the SERVICE! message in the display.
i) Press and hold the right RESET knob.
ii) Turn on the ignition – do not start the engine.
iii) Release the knob.
4. Do the following to display the next service interval (SERVICE IN ##MI)
i) Press and hold the right RESET knob.
ii) Release the knob.
5. Turn off the ignition.
6. Start the engine and verify indicator has been reset.
2000-2003
BMW recommends the use of a reset tool.
Manual Reset
1. Turn off the ignition.
2. Press and hold the TRIP ODOMETER button in the instrument cluster and turn the ignition to Accessory.
3. Keep the button pressed for 5 seconds until OIL SERVICE RESET (RE) or INSPECTION RESET (RE) appears in the display. Then release the button.
4. Press and hold the button again for 5 seconds until RE or RESET flashes in the display. Then release the button.
5. With the display flashing
6. Turn the ignition off and start the engine to verify the indicator has been reset.
2004-2005
BMW recommends the use of a reset tool.
Manual Reset
1. Turn off the ignition.
2. Press and hold the TRIP ODOMETER button in the instrument cluster and turn the ignition to Accessory.
3. Keep the button pressed for 5 seconds until OIL SERVICE RESET (RE) or INSPECTION RESET (RE) appears in the display. Then release the button.
4. Press and hold the button again for 5 seconds until RE or RESET flashes in the display. Then release the button.
5. With the display flashing
6. Turn the ignition off and start the engine to verify the indicator has been reset.
2006-2012
BMW recommends the use of a reset tool.
Manual Reset
1. Turn ignition to Terminal 15 which is one turn of the key or one press of the START/STOP button.
2. Press and hold the Instrument Cluster Set/Reset button for 10 seconds.
3. The upper display in the Instrument Cluster will be illuminated with a Service Item. The lower display in the Instrument Cluster will indicate the remaining time or mileage left for that Service Item. Pressing the button repeatedly will allow the display to scroll through all of the Condition Based Service Items.
4. Press and hold the Instrument Cluster Set/Reset button again and the lower display screen will indicate “”OK”” or “”DUE””.”
5. Pressing the Instrument Cluster Set/Reset button again will allow the “”RESET”” to appear in the lower window for that service. Releasing and reapplying the button one more time will reset the service displayed in the upper window only. ”
6. Turn the ignition off and start the engine to verify the indicator has been reset.