2004-2005
Turn the ignition to run (one position before starting engine).
Press the “MAINT” button until “Engine Oil” appears in the display.
To reset the driving distance push the “MAINT” or “TRIP RESET” button for more than 1.5 seconds.
Turn the ignition off and then start the engine to verify the indicator has been reset. Turn the ignition on without starting the engine (press START/STOP) button.
2006-2008
Navigation System:
Press the “TRIP” button repeatedly until “MAINTENANCE appears and press enter to select.
Use the joystick to scroll to “Engine Oil” and press “ENTER” button.
Select “RESET” and press “ENTER” button.
Turn the ignition off and then start the engine to verify the indicator has been reset.
Whitout navigation System:
Press the “MAINT” button until “Engine Oil” appears in the display.
Use the controller keys to select “Engine Oil” and press “Enter”.
Select “RESET” and press “ENTER” button.
Navigation System:
Turn the ignition off and then start the engine to verify the indicator has been reset.
2009-2010
Turn the ignition on without starting the engine (press START/STOP) button.
Locate TRIP computer switches on the right side of the instrument panel (Square and Circle buttons).
Press Square (button) repeatedly to bring up the “Setting” screen on the instrument panel display.
Follow the prompts to select the “Maintenance” menu. Once this menu is accessed follow the prompts to set or reset the “Engine Oil”.
Repeat and follow prompts to reset “Oil Filter”.
Turn the ignition off and then start the engine to verify the indicator has been reset.
Turn the ignition to run (push START/STOP button once).
Press the (square) button, located on the instrument panel just behind the steering wheel to the left, to display the SETTINGS mode.
In the setting mode screen press (circle) button to move to MAINTENANCE.
Set a desired interval by pushing (circle) button to highlight ENGINE OIL and pressing (square) button The reset mode will open up and allow you to enter the desired distance.
Select RESET and select new time or distance.
Repeat step 3 for ENGINE OIL FILTER. Turn the ignition off and then start the engine to verify the indicator has been reset.
How to reset the Maintenance Service interval:
Metod 1
– Switch ignition on to position one, (first click clockwise);
– “Outside temperature” should be displayed, if not move to it (You have to be in this display to go further);
– Press the trip odometer, “reset”, knob three times consecutively ( The Voltage display will appear);
– Press Down Arrow to enter the “Service Menu”. “Service Data” submenu below will be highlighted.
– Press right page to enter the Service data submenu. (Left page goes up in menus, -+ selects items displayed)
– Press – three times on right of wheel to highlight “Confirmation”.
– Use right page to select to display sub-menu as to what to confirm.
– Select “Full Service” (No need to use -+.) to confirm this choice
– Press right page to confirm. (Delay is about 3 seconds.)
– Press left page twice to exit the menu system, or turn off the ignition switch.
– Turn off ignition. Turn back on. The display should show that it is recalculating the mileage and days. This takes about 60 seconds so be patient.
Metod 2
1. Put the key in the ignition and switch it on without starting the engine.
(Wait for LCD to return to the vehicle mileage)
2. Hold the “O” button down till you hear a beep (could take a while, 30 sec.)
3. Press the M button repeatedly and a number of reset menus will appear, (If you have used oil according to quality sheet 229.31 or 228/229.51 you can scroll to Reset.31 or Reset.51 respectively.) Select “reset 51”
4. Now, when appropriate oil type is selected press “O” for 6 seconds until ”2” is displayed.
5. Press “O” once again briefly and the ” reset done” message will confirm that the job is done.
6. Pull the Key out
FOR THE 2004 DODGE SPRINTER!
Turn the key to position 2 in the ignition lock and immediately press the button MI (km) twice.
Within 10 seconds, return the key to the 0 in the ignition lock.
Press and hold the button MI (km). Turn the key to position 2 in the ignition lock. Keep the button MI (km) pressed.
The maintenance indicator with the time/distance is shown.
After about 10 seconds, an acoustic signal will sound and the maintenance indicator is displayed with the new remaining time / distance .
Release the button MI (km)
Turn the key to position 2in the steering lock and immediately press the KM button twice briefly.
Within 10 seconds, turn the key back to position 0 in the steering lock.
Press and hold down the KM button. Turn the key to position 2 in the steering lock. Hold the KM button down for a further 10 seconds.
The service indicator with current remaining distance/remaining time appears.
After about 10 seconds, an acoustic signal will sound and the service displaywith the new remaining distance/remaining time will appear for about 10 seconds.
Relaese the KM button.
All quoted direct from the handbook! It took me a couple of goes to get it to reset (lack of counting ability maybe!) but I got it reset in the end.