1996-1997
Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds. If the CHANGE OIL SOON indicator flashes 2 times, the system is reset.
Turn the ignition off and then start the engine to verify the indicator has been reset.
1998-2004
With Driver Information Centre:
Turn the ignition to run (one position before starting engine).
Press the trip calculator MODE button until the light appears next to OIL LIFE.
Press and hold the trip calculator RESET button until the oil life percentage changes to 100%.
Turn the ignition off and then start the engine to verify the indicator has been reset.
Without Driver Information Centre:
Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds. If the CHANGE OIL SOON indicator flashes 2 times, the system is reset.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2005-2010
Turn the ignition to run (one position before starting engine).
Press the OPTIONS button on the Driver Information Centre until ENGINE OIL MONITOR appears on DIC screen.
Press the SET/RESET button to reset the system. The next screen indicates that the engine oil monitor system has been reset. If the vehicle is equipped with the trip computer DIC, when the GAUGE button is pressed and the OIL LIFE REMAINING mode appears, it should read 100% OIL LIFE REMAINING appears, it should read 100 percent OIL LIFE REMAINING.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2006-2008
Turn the ignition to run (one position before starting engine).
Maintenance and tire pressure information will be displayed when the “MAINT” button is pushed on the centre console.
To display the setting of the maintenance interval, select the “Engine Oil” key using the joystick and push the “ENTER” button.
To reset the maintenance interval, select the “Reset” key using the joystick and push the “ENTER” button.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2009-2010
Turn the ignition to run (push START/STOP button once).
Switches for the trip computer are located on the right side of the combination meter panel. When the ignition switch is pushed to the ON position press the (square) button to bring up “Setting” and and press (circle) button to select.
Use the (circle) button to scroll to MAINTENANCE and use the (square) button to select.
Select ENGINE OIL to set or reset the distance for changing the oil.
Repeat step 2 to set or reset the distance for the OIL FILTER.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2009-2010
Turn the ignition to run (one position before starting engine). The maintenance information (the wrench symbol and distance to change a maintenance item) comes on for about 5 seconds and then turns off.
Push the trip computer mode switch A for 3 seconds while the wrench symbol and maintenance information are displayed. The symbol and distance display will start flashing and the display shows the current interval (ie. 5000KM).
Push the switch A to increase the interval distance. Each step increases the interval by 1000km. The interval distance can be set up to 30000km after the display returns to 0.
If no further action is made, the display returns to the previous mode and the new interval is set. If the interval distance is set to 0, the display will skip the maintenance information when the ignition is placed in run or start mode.
2002-2006
*Diagnostic Reset Tool Required (please refer to TOOLS page)
2007-2010
*Diagnostic Reset Tool Required (please refer to TOOLS page)
Manual Reset:
Turn ignition to Terminal 15 which is one turn of the key or one press of the START/STOP button.
Press and hold the trip odometer reset button for approximately 10 seconds until the first service job appears in the display.
The upper display in the Instrument Cluster will be illuminated with a Service Item (example: An oil can is the designation for Oil Service). The lower display in the Instrument Cluster will indicate the remaining time or mileage left for that Service Item (example: 14000). Press the on-board computer button repeatedly (located on the direction indicator/main-beam switch) to scroll through all of the Condition Based Service Items.
Press and hold the on-board computer button on the direction indicator/main-beam switch until “RESET” appears in the lower display.
Pressing the on-board computer button again resets the service shown in the upper display. Repeat the procedure for each additional service which is to be reset.
Turn the ignition off and start the engine to verify the indicator has been reset.
2004-2005
Turn the ignition to run (one position before starting engine).
Press the “MAINT” button until “Engine Oil” appears in the display.
To reset the driving distance push the “MAINT” or “TRIP RESET” button for more than 1.5 seconds.
Turn the ignition off and then start the engine to verify the indicator has been reset. Turn the ignition on without starting the engine (press START/STOP) button.
2006-2008
Navigation System:
Press the “TRIP” button repeatedly until “MAINTENANCE appears and press enter to select.
Use the joystick to scroll to “Engine Oil” and press “ENTER” button.
Select “RESET” and press “ENTER” button.
Turn the ignition off and then start the engine to verify the indicator has been reset.
Whitout navigation System:
Press the “MAINT” button until “Engine Oil” appears in the display.
Use the controller keys to select “Engine Oil” and press “Enter”.
Select “RESET” and press “ENTER” button.
Navigation System:
Turn the ignition off and then start the engine to verify the indicator has been reset.
2009-2010
Turn the ignition on without starting the engine (press START/STOP) button.
Locate TRIP computer switches on the right side of the instrument panel (Square and Circle buttons).
Press Square (button) repeatedly to bring up the “Setting” screen on the instrument panel display.
Follow the prompts to select the “Maintenance” menu. Once this menu is accessed follow the prompts to set or reset the “Engine Oil”.
Repeat and follow prompts to reset “Oil Filter”.
Turn the ignition off and then start the engine to verify the indicator has been reset.