1994-2002
Turn the ignition to run (one position before starting engine).
This message can be deleted by first briefly pressing the CLR button, then depressing it a second time for at least 8 seconds until “SERVICE” appears on the display and a chime sounds.
Turn the ignition off and then start the engine to verify the indicator has been reset.
*The message can only be deleted when it is shown on the SID (Service Indicator Display).
2003-2006
Turn the ignition to run (one position before starting engine).
Press the CUSTOMIZE button.
Select System Settings using the INFO dial. Press the INFO dial.
Select Service Info. Press in the INFO dial.
Select Reset Service Ind. Press in the INFO dial.
When asked Are you sure? Select Yes. Turn the ignition off and then start the engine to verify the indicator has been reset.
2007-2009
Turn the ignition to run (one position before starting engine).
Select Settings using the steering wheel controls (up or down arrow).
Press and hold the SET button until given audible confirmation.
Select Time for Service.
Press the SET button.
To the question Reset Service Ind? Select YES. Turn the ignition off and then start the engine to verify the indicator has been reset.
Page 52 of the Owner’s Manual gives the answer to this:
1. Switch off the ignition and press the reset knob of the trip counter below the speedometer and hold.
2. Switch on the ignition and release the reset button, one of the service events appear in the display.
3. It is possible to switch between the the readouts of the service events by briefly pressing the reset button.
4. When the particular service event is displayed, turn the button for setting the digital clock to the right, “service—” appears in the display.
5. Switch off the ignition. Only now is the service event reset.
Page 52 of the Owner’s Manual gives the answer to this:
1. Switch off the ignition and press the reset knob of the trip counter below the speedometer and hold.
2. Switch on the ignition and release the reset button, one of the service events appear in the display.
3. It is possible to switch between the the readouts of the service events by briefly pressing the reset button.
4. When the particular service event is displayed, turn the button for setting the digital clock to the right, “service—” appears in the display.
5. Switch off the ignition. Only now is the service event reset.
BMW 2001 to current
Ignition Off (Position 0)
Press and Hold the trip odometer button while turning key to position 1 (ACCESSORY)
Keep the button depressed (about 5 secs.) until you see “Oil Service” or “Inspection” with “Reset” or “Re” in the display*
Press the button again and hold for approx. 5 secs. until “Reset” or “Re” flashes
While the display is flashing, briefly press the button again to reset the Service Interval. After the display has shown the new interval you should see “END SIA” for about 2 seconds
Note: that if the “Reset” or “Re” does not flash, then you have not met the minimum consumption level and cannot reset
*Note: On vehicles with “High” cluster, you will also see the amount of fuel (in litres) remaining until next service
How to reset the Maintenance Service interval:
Metod 1
– Switch ignition on to position one, (first click clockwise);
– “Outside temperature” should be displayed, if not move to it (You have to be in this display to go further);
– Press the trip odometer, “reset”, knob three times consecutively ( The Voltage display will appear);
– Press Down Arrow to enter the “Service Menu”. “Service Data” submenu below will be highlighted.
– Press right page to enter the Service data submenu. (Left page goes up in menus, -+ selects items displayed)
– Press – three times on right of wheel to highlight “Confirmation”.
– Use right page to select to display sub-menu as to what to confirm.
– Select “Full Service” (No need to use -+.) to confirm this choice
– Press right page to confirm. (Delay is about 3 seconds.)
– Press left page twice to exit the menu system, or turn off the ignition switch.
– Turn off ignition. Turn back on. The display should show that it is recalculating the mileage and days. This takes about 60 seconds so be patient.
Metod 2
1. Put the key in the ignition and switch it on without starting the engine.
(Wait for LCD to return to the vehicle mileage)
2. Hold the “O” button down till you hear a beep (could take a while, 30 sec.)
3. Press the M button repeatedly and a number of reset menus will appear, (If you have used oil according to quality sheet 229.31 or 228/229.51 you can scroll to Reset.31 or Reset.51 respectively.) Select “reset 51”
4. Now, when appropriate oil type is selected press “O” for 6 seconds until ”2” is displayed.
5. Press “O” once again briefly and the ” reset done” message will confirm that the job is done.
6. Pull the Key out
FOR THE 2004 DODGE SPRINTER!
Turn the key to position 2 in the ignition lock and immediately press the button MI (km) twice.
Within 10 seconds, return the key to the 0 in the ignition lock.
Press and hold the button MI (km). Turn the key to position 2 in the ignition lock. Keep the button MI (km) pressed.
The maintenance indicator with the time/distance is shown.
After about 10 seconds, an acoustic signal will sound and the maintenance indicator is displayed with the new remaining time / distance .
Release the button MI (km)