Lexus
How to reset oil change light indicator reset maintenance light without using a computer for Lexus
How to reset oil change light indicator reset maintenance light without using a computer for Lexus
1. Start the car and set the odometer to the total vehicle miles setting
2. Turn off the car
3. Hold in the odometer button
4. Turn the car on by pressing ‘start’ twice but DO NOT start the car (don’t press the break peddle)
5. Continue to hold the odometer button in until it resets to all zeros
6. Let it go
2006-2010
Turn the ignition to run (one position before starting engine) and bring up the odometer reading. Turn the ignition off.
While holding down the “RESET” button turn the ignition to run (one position before starting engine). Continue to hold the button for longer than 5 seconds. If the system fails to reset, the light will continue flashing.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2005-2006
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the ODO/TRIP knob then the turn ignition off.
Hold down ODO/TRIP knob while turning the ignition key to the run position (one position before starting engine).
Hold down the knob until the light goes off. Before the light goes off, it illuminates
3 seconds, flashes for 2 seconds and illuminates for 1 second. If the system fails to reset, the light will remain flashing. In this case, return to step 1 and try again.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2007
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the ODO/TRIP knob then the turn ignition off.
Hold down ODO/TRIP knob while turning the ignition key to the run position (one position before starting engine) for longer than 7 seconds. While doing this operation, the “engine oil replacement” reminder light goes off. If the system fails to reset, the light will remain flashing. In this case, return to step 1 and try again.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2008-2010
Turn the engine on by holding the START/STOP switch. Use the trip meter switch to bring up the trip meter A reading. Turn the ignition off.
While pressing the trip meter reset button, set the engine switch to run (push START/ STOP button once) and continue to press and hold the knob until the multi information display indicates that the reset is complete.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2004
Turn the ignition to run (one position before starting engine).
Press ODO/TRIP button to display odometer mode. Turn ignition off.
While pressing ODO/TRIP button, turn ignition to run (one position before starting engine). Continue to hold the button for longer than 5 seconds.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2005-2006
Turn the ignition to run (one position before starting engine).
Push the “TRIP” button to change the trip meter display to blank. Turn the ignition off.
While pressing the trip meter “RESET” button, turn ignition to run (one position before starting engine). Continue to hold the button for longer than 5 seconds.
“Mileage Reset” appears on the display, the master warning light comes on, and a warning tone sounds.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2007
Turn the ignition to run (one position before starting engine). Use the trip meter switch to bring up the trip meter A reading.Turn the ignition off.
While pressing the trip meter reset button, set the engine switch to run (one position before starting engine) and continue to press and hold the knob until the multi information display indicates that the reset is complete.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2008-2010
Turn the engine on. Use the trip meter switch to bring up the trip meter A reading. Turn the ignition off.
While pressing the trip meter reset button, set the engine switch to run (push START/ STOP button once) and continue to press and hold the knob until the multi information display indicates that the reset is complete.
Turn the ignition off and then start the engine to verify the indicator has been reset.