2005-2006
Turn the ignition to run (one position before starting engine).
The VEHICLE INFORMATION screen will appear when the INFO button is pushed. Choose an item “MAINTENANCE” using the joystick and push the ENTER button.
Select the “Engine Oil” setting using the joystick and press ENTER.
To reset the maintenance interval, select the RESET key using the joystick and press the ENTER button.
Repeat steps for “Oil Filter” reset.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2007-2010
Turn the ignition on without starting the engine (press START/STOP) button.
Locate TRIP computer switches on the right side of the instrument panel (Square and Circle buttons).
Press Square (button) repeatedly to bring up the “Setting” screen on the instrument panel display.
Follow the prompts to select the “Maintenance” menu. Once this menu is accessed follow the prompts to set or reset the “Engine Oil”.
Repeat and follow prompts to reset “Oil Filter”.
Turn the ignition off and then start the engine to verify the indicator has been reset.
Tag: vehicle
Reset service indicator citroen piccaso
To reset the service light on your vehicle is a straight forward procedure. Ignition off , Hold down the left dash button with the 000 s on . Whilst holding the button turn on the ignition and watch the display count down to 0 . Turn ignition off then on again and there you have it. Magic. Obviously this should be done in conjunction with a routine service to insure your car is safe reliable and legal .
Reset the On-Board Computer for a 2003 Ford Fiesta
1. Pull the hood release to open the hood. Prop it up with a rod and locate the battery under the hood.
2. Find the negative battery terminal. You will see a clamp with a nut on it. Loosen the nut with an adjustable wrench and slid the clamp off of the battery terminal.
3. Wrap a towel around the negative battery clamp and keep it away from the battery altogether. The towel will help to protect you and the battery.
4. Let the vehicle sit for about 15 minutes. This will allow the computer to reset and erase all trouble codes.
5. Discard the towel and put the negative battery clamp back onto the negative battery terminal. Tighten the nut with the wrench. Tuck the rod away and lower the hood of the car.
6. Put the key into the ignition and start the engine. Verify that all service and warning lights have turned off.
Service reset on computer display for VW Sharan V6 2003 model
Press and hold the R/H button.
Switch ignition on.
The word service will appear in the trip recorder display.
Release button.
Turn L/H button to the right to reset the display.
Switch ignition off.
Sorted!
This will not work if the vehicle is on longlife service intervals!
Service reset VW Crafter 2.5 td
VW Crafter service reset Sitting in the drivers seat looking at the dash on the left hand side you have a M button and below it a 0 button these are the buttons you will need to use.
When i refer to the LCD this is the illuminated part in the middle that shows your mileage,service mileage and trip mileage.
Please read this fully first to get the jist of it as if you perform the actions too slow it wont work and you will have to start over.
1.Put on ignition
2.Wait for service mileage to revert to vehicle mileage
3.When it reverts to the vehicle mileage press and hold the 0 button until you hear a beep (can take up to 30 seconds)
4.As soon as you hear the beep press the M button repeatdly and you will see in the LCD display different reset’s the one you need to select is “reset 51” if you go past it just keep pressing the M button till it comes up again.
5.When the “reset 51” is displayed stop pressing the M button then press and hold the 0 button again until a number 2 is displayed in the LCD.
6.Release the 0 button and then press twice and it will say in the LCD reset done ,if it is not reset you will get a 30% power reduction after 2K miles