Well after a small but required service on the car I had to reset the warning light. The real quick deal to reset all the requested lights on Rover 75 is to do the following
Get a small wire, Turn the key to second position, Short Pin 8 and Pin 4 on the OBD connector for “4 seconds to reset oil light”, “8-25 seconds for the other 2 lights” and this will reset the 15000 service request for oil change. Quick and easy and not legal if you do it without actually doing the service.
S80
Turn ignition switch to position I
Press and hold “day counter reset button”
Turn ignition to position II
Continue holding day counter for about 10 seconds
While SRL flashes, release day counter button
Should hear “beep-beep” to confirm command accepted
The service light on these vehicles is usually a spanner / wrench symbol. To reset that indicator:
Turn the Ignition ON (position 2) but do not start the engine
(On cars with keycard ignition, insert the card, then press and hold the start button for 5 seconds to turn on the dash cluster)
Press the button on the end of the wiper stalk repeatedly until the spanner symbol and miles to service appears on the display
(Some models have 2 buttons, which cycle through the options in opposite directions – either button can be used in this case)
Press and hold the button
The display will now change to the new service interval and start flashing
Keep holding the button until the display stops flashing
Release the button
Press and hold the odometer reset button
Turn the ignition key to position 2
After 30 seconds release the odometer reset button
Turn ignition off
You may notice the display flashing or counting down.
Toyota 4Runner 2003-onwards
With the ignition “OFF”, press and hold “RESET” button. Turn ignition to the “ON” position. Continue to hold button until “MAINT REQD” light turns off.
Turn ignition off.
Camry 2004-onwards
With the ignition “OFF”, press and hold button below the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Corolla
Turn the key to the off position. Press and hold down the trip meter button and turn the key to the “on” position. Continue to hold the trip button for 5 seconds after the key is turned on, then release.
Highlander 2004-onwards
With the ignition “OFF”, press and hold button below the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Matrix 2004-onwards
With the ignition “OFF”, press and hold button below the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Prius 2004-onwards
With the “POWER” switch off, press and hold “ODO TRIP” button. Press “POWER” switch twice selecting “IG-ON”. Continue to hold button until”000000″ is displayed and “MAINT REQD” light turns off. Turn “POWER” switch to off.
RAV4 2004-onwards
With the ignition “OFF”, press and hold button below the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Sequoia 2004-onwards
With the ignition “OFF”, press and hold button below the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Sienna 2004-onwards
With the ignition “OFF”, press and hold button to the right of the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″
is displayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Solara 2004-onwards
With the ignition “OFF”, press and hold button to the left of the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Tacoma 2005-onwards
With the ignition “OFF”, press and hold button to the right of the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″
is displayed and the “MAINT REQD” lamp turns off. Turn ignition off.
Tundra 2003-onwards
With the ignition “OFF”, press and hold button below the speedometer. Turn ignition to the “ON” position. Continue to hold button until “000000″ isdisplayed and the “MAINT REQD” lamp turns off. Turn ignition off.