Tag: time

RESET MAINTENANCE LIGHT ON DODGE SPRINTER

Reset maintenance light on Dodge Sprinter

1. Put the key in the ignition and switch it on without starting the engine.
(Wait for LCD to return to the vehicle mileage)
2. Hold the “O” button down till you hear a beep (could take a while, 30 sec.)
3. Press the M button repeatedly and a number of reset menus will appear, (If you have used oil according to quality sheet 229.31 or 228/229.51 you can scroll to Reset.31 or Reset.51 respectively.) Select “reset 51″
4. Now, when appropriate oil type is selected press “O” for 6 seconds until ”2” is displayed.
5. Press “O” once again briefly and the ” reset done” message will confirm that the job is done.
6. Pull the Key out
FOR THE 2004 DODGE SPRINTER!

Turn the key to position 2 in the ignition lock and immediately press the button MI (km) twice.
Within 10 seconds, return the key to the 0 in the ignition lock.
Press and hold the button MI (km). Turn the key to position 2 in the ignition lock. Keep the button MI (km) pressed.
The maintenance indicator with the time/distance is shown.
After about 10 seconds, an acoustic signal will sound and the maintenance indicator is displayed with the new remaining time / distance .
Release the button MI (km)

Reset service light, maintance on Toyota Rav 4

This Maintenance light is a reminder : “TIME FOR AN OIL CHANGE!”

1. Turn the ignition key to the ‘OFF’ position with the trip meter A reading shown.

2. Turn the ignition key to the ‘ON’ position while holding down the trip meter ‘RESET’ button.

3. Hold down the knob for at least 5 seconds. The odometer indicates ‘000000’ and the light goes off.

BMW X5 2002 Oil Reset

BMW X5 Engine Oil Service reset

Turn the ignition to “0”
Press and hold odometer button and turn the ignition to “1”.
Hold odometer button pressed for approximately 5 seconds until the display shows: “Inspektion Re /
Release and press odometer button again until Reset flashes
Release and press odometer button shortly.
Release and press odometer button again.
The next oil service interval will be shown and will disappear.
Oil service lamp is now reset

Note: To abort the procedure at any time: turn the ignition to “0”.

Reset Service light for 2006 Volvo XC90

“Resetting the service reminder indicator (SRI), model years 2002-
The service reminder indicator (SRI) informs the driver that it is time for the car to be serviced. The text message is displayed for 120s each time the ignition is switched on.
Proceed as follows to reset the service reminder indicator (SRI):

1.Ignition position I
2. Press and hold in the reset button for the trip odometer
3. Ignition position II. Note! Turn the key to position II within 2 seconds
4. Hold the reset button for the trip meter pressed in until the original value has been reset. Note! For all vehicles from the 2003 model year a general yellow lamp will light when the reset button must be released
5. Release the reset button for the trip odometer within 4 seconds. The instrument gives an audible signal when resetting has succeeded
6. If the trip meter is already reset the reset button should be held in for a minimum of 10 seconds and a maximum of 14 seconds.

Note! If the reset button for the trip odometer is not released within 4 seconds, the service reminder indicator (SRI) is not reset.”

Volvo 850-70 Service Light Reset

RESETTING 5000 MILE SERVICE LAMP ON 1994 + 1995 850

NOTE: This function is for the service reminder lamp, be sure you have performed the proper service such as changing the oil before resetting. If the check engine lamp is illuminated when the car is running, you’ll need to have the car looked at by the Volvo dealer for proper diagnosis.

1. Turn on the ignition to the KPII position so the warning lamps on the dash are illuminated. Do not start the car.

2. Open the bonnet of the car and locate Diagnostic test port (A) behind the driver side headlamp.

3. Remove the cover and pull the jumper wire out of the holder in the cover.

4. Insert the jumper into terminal #7, then press button 4 times, wait approximately 5 seconds and the red lamp should glow continuously. You are now in the data reset mode.

5. Press the button 1 time and wait approximately 5 seconds for the lamp to glow again then press the button 5 times. After about 5 seconds the lamp will illuminate again, press the button 1 time and you will see the lamp flash repeatedly for a couple of seconds indicating that the service lamp has been properly reset.

6. If a mistake is made, simply switch the ignition off and back on to reset and start over.

1996 Model (Some of them)
On these models the diagnostic socket is in front of the gear stick. Switch the ignition on. As you look at the speedometer on the dash, beneath it opposite the trip reset button is a rubber plug. Remove the plug and with a thin pointer such as a ball point pen, depress the pin. This will reset the service light.

1999 Model Service Lamp Reset Procedure

1. Press and hold trip odometer reset button

2. Turn ignition key to run position KPII (not the start position)

3. Wait 30 seconds or until service light begins blinking

4. Release Trip Odometer button

5. Turn ignition to off position