First you press the odometer button then at the same time you put the key in “on” no engine running, wait for 30 secs aprox and it will be reset, repeat this steps for the oil light
what is the odometer button
Tag: time
Reset Your Service Light Peugeot
If that spanner symbol has come up on your dashboard then it’s time your car was due a service. The symbol is just a periodic reminder, it doesn’t actually come up to denote a fault – the ‘check engine’ symbol does that.
If you service the car yourself and want to reset it or your garage has forgotten to reset it, you can do it yourself quite easily with the following simple steps:
This will work with the following models:
Peugeot 106 (1999 on)
Peugeot 206 (1998 on)
Peugeot 306 (1996 on)
Peugeot 307 (1996 on)
Peugeot 406 (1998 on)
Peugeot 607 (2000 on)
Peugeot 806 (1999 on)
Peugeot Expert (1999 on)
Peugeot 807 (2002 on)
Peugeot Partner (1999 on)
Peugeot Boxer (2002 on)
Procedure to Reset Peugeot Service Light as follows:
1. Switch the Ignition Off
2. Press and hold the tripmeter (mileage reset) button on the dash
3. Now switch the ignition to the ON position
4. Keep the button pressed for 10 seconds
5. The display will read ‘0’ and the service symbol will extinguish. Job done.
service light reset Audi A2 (2000-2005), A3 (2000-2003), A6 2000 to 2004)
Audi A2 (2000-2005), A3 (2000-2003), A6 2000 to 2004)
For Fixed Interval servicing, you can use the following procedure:
Start with the ignition turned OFF
Press and hold the button on the right side of the display while turning the ignition on (position 2)
“SERVICE IN xxx Miles / Kilometres” or “SERVICE !” should be displayed on the dashboard
Release the button on the right
To reset on the existing service schedule, press and hold the button on the left side of the display until the NEW distance or time value appears
Release the button on the left
Turn off the ignition
service light reset Renault Trafic (2001-present), Vauxhall Movano (2007- present), Vivaro (2007-present)
Turn the Ignition ON (position 2) but do not start the engine
Within 100 seconds of turning the key, press the accelerator pedal to the floor and hold it down
While still holding down the accelerator, press and release the brake pedal twice, then press it a 3rd time and hold it down
Release both pedals
Within around 10 seconds, the Oil Service warning light should turn off
Immediately Turn Ignition OFF, then within 3 seconds turn it back ON (position 2)
Turn Ignition back OFF to complete
service light reset SPRINTER
How to reset the Maintenance Service interval:
Metod 1
– Switch ignition on to position one, (first click clockwise);
– “Outside temperature” should be displayed, if not move to it (You have to be in this display to go further);
– Press the trip odometer, “reset”, knob three times consecutively ( The Voltage display will appear);
– Press Down Arrow to enter the “Service Menu”. “Service Data” submenu below will be highlighted.
– Press right page to enter the Service data submenu. (Left page goes up in menus, -+ selects items displayed)
– Press – three times on right of wheel to highlight “Confirmation”.
– Use right page to select to display sub-menu as to what to confirm.
– Select “Full Service” (No need to use -+.) to confirm this choice
– Press right page to confirm. (Delay is about 3 seconds.)
– Press left page twice to exit the menu system, or turn off the ignition switch.
– Turn off ignition. Turn back on. The display should show that it is recalculating the mileage and days. This takes about 60 seconds so be patient.
Metod 2
1. Put the key in the ignition and switch it on without starting the engine.
(Wait for LCD to return to the vehicle mileage)
2. Hold the “O” button down till you hear a beep (could take a while, 30 sec.)
3. Press the M button repeatedly and a number of reset menus will appear, (If you have used oil according to quality sheet 229.31 or 228/229.51 you can scroll to Reset.31 or Reset.51 respectively.) Select “reset 51”
4. Now, when appropriate oil type is selected press “O” for 6 seconds until ”2” is displayed.
5. Press “O” once again briefly and the ” reset done” message will confirm that the job is done.
6. Pull the Key out
FOR THE 2004 DODGE SPRINTER!
Turn the key to position 2 in the ignition lock and immediately press the button MI (km) twice.
Within 10 seconds, return the key to the 0 in the ignition lock.
Press and hold the button MI (km). Turn the key to position 2 in the ignition lock. Keep the button MI (km) pressed.
The maintenance indicator with the time/distance is shown.
After about 10 seconds, an acoustic signal will sound and the maintenance indicator is displayed with the new remaining time / distance .
Release the button MI (km)