Tag: start

Reset service light, maintance on Toyota Land Cruiser

1. Turn your ignition key to the ‘ACC’ or ‘LOCK’ position.
2. Press and hold the trip meter reset nob (next to your Toyota Land Cruiser’s odometer).
3. While holding the trip meter reset nob, turn the ignition to ‘ON’, but do not start your Toyota Land Cruiser.
4. Hold the meter reset until the MAINT REQD light switches off.

If this procedure does not successfully reset your maintenance required light, make sure that your digital odometer is set with the odometer reading showing and try again. If the light is still lit, you can try disconnecting your Toyota Land Cruiser battery, causing the internal computer to reset. If you still haven’t successfully turned off the oil indicator MAINT REQD light, please read your manual or contact your dealer for further instruction!

Reset service light Toyota Yaris 2009 – 2010

1. Turn the ignition to run (one position before starting engine).

2. Ensure odometer reading is shown, turn ignition off.

3. While holding down the trip meter reset knob turn the ignition to run (one position before starting engine).

4. Hold down knob for at least 5 seconds. The odometer indicates “000000″ and the light goes off. If the system fails to reset, the light will continue flashing.

5. Turn the ignition off and then start the engine to verify the indicator has been reset.

Reset the service indicator light 2007 Renault clio

Turn on the ignition, but don’t start the car. On the right stalk there is a toggle switch that hinges up and down, and is used for going through the different features of the display. When the display shows ‘Service Due’ press and hold the top part of this switch for 10 seconds until the dispaly resets and it shows 30,000km or whatever until next service.
Turn on the ignition, but don’t start the car. On the right stalk there is a toggle switch that hinges up and down, and is used for going through the different features of the display. When the display shows ‘Service Due’ press and hold the top part of this switch for 10 seconds until the dispaly resets and it shows 30,000km or whatever until next service.

all of the above is correct apart from pressing the toggle button. if you instead press the bottom toggle button for 10 seconds the display will start to flash. Keep button depressed and 5 seconds later the service counter will reset.

Volvo 850-70 Service Light Reset

RESETTING 5000 MILE SERVICE LAMP ON 1994 + 1995 850

NOTE: This function is for the service reminder lamp, be sure you have performed the proper service such as changing the oil before resetting. If the check engine lamp is illuminated when the car is running, you’ll need to have the car looked at by the Volvo dealer for proper diagnosis.

1. Turn on the ignition to the KPII position so the warning lamps on the dash are illuminated. Do not start the car.

2. Open the bonnet of the car and locate Diagnostic test port (A) behind the driver side headlamp.

3. Remove the cover and pull the jumper wire out of the holder in the cover.

4. Insert the jumper into terminal #7, then press button 4 times, wait approximately 5 seconds and the red lamp should glow continuously. You are now in the data reset mode.

5. Press the button 1 time and wait approximately 5 seconds for the lamp to glow again then press the button 5 times. After about 5 seconds the lamp will illuminate again, press the button 1 time and you will see the lamp flash repeatedly for a couple of seconds indicating that the service lamp has been properly reset.

6. If a mistake is made, simply switch the ignition off and back on to reset and start over.

1996 Model (Some of them)
On these models the diagnostic socket is in front of the gear stick. Switch the ignition on. As you look at the speedometer on the dash, beneath it opposite the trip reset button is a rubber plug. Remove the plug and with a thin pointer such as a ball point pen, depress the pin. This will reset the service light.

1999 Model Service Lamp Reset Procedure

1. Press and hold trip odometer reset button

2. Turn ignition key to run position KPII (not the start position)

3. Wait 30 seconds or until service light begins blinking

4. Release Trip Odometer button

5. Turn ignition to off position

Reset oil change light on a 2008 dodge nitro

1. Turn the ignition key to ON but do not start the engine.
2. Slowly depress the accelerator to the floor and release it three times within 10 seconds.
3. Turn the ignition key to the OFF position.