Service light reset on Peugeot Citroen inc 206 106 saxo

There’s no great “trade secret” as to how to reset the service indicator lamp on most Peugeot / Citroen, simply refer to pages in the Owner’s Handbook!

For reference of those interested in such matters, but who might not have access to an owner’s manual, this is the procedure to follow:

1) Ensure “ignition” key is turned off.
2) Depress and hold the odometer reset button whilst turning the “ignition” switch to the on position.
3) Keep the odometer reset button depressed for 10 seconds whilst the service display counts down from 10 to 0. When the count down reaches zero the spanner icon will vanish from the display and the service indicator will be reset.

Note 1: When reset, the service indicator is actually reset to 9,500 miles. The mileage that the car accumulates henceforth is subtracted from 9,500 miles, until 9,500 miles have elapsed at which point the service indicator icon will reappear inorder to warn the driver that the next service is imminent. Any mileage accumulated beyond 10,000 miles since the last reset will be indicated with a minus sign displayed infront of the mileage to indicate by how much a service is overdue.

Note 2: To the best of my knowledge, the above service light reset procedure applicable to most Peugeot cars, most Citroen cars and most Fiat cars with the exception of the Fiat Stilo. (Also applicable to car derrived vans from the above ranges).

Service interval reset Skoda Octavia

For oil press and hold the right hand button on the cluster – oil will appear in the display – release right hand button then turn left hand button clockwise until —– appears.

For insp prees and hold right hand button – turn on ignition – release button then press and release button again – insp will appear in the display – turn left hand button as before until —– appears.

note: if you’re clearing the insp service sometimes it’s neccessary to clear the oil service afterwards (if it wasn’t done at oil service)

Skoda Octavia II (2004 – ) – 07 1.8 Service Interval Display

Page 52 of the Owner’s Manual gives the answer to this:

1. Switch off the ignition and press the reset knob of the trip counter below the speedometer and hold.

2. Switch on the ignition and release the reset button, one of the service events appear in the display.

3. It is possible to switch between the the readouts of the service events by briefly pressing the reset button.

4. When the particular service event is displayed, turn the button for setting the digital clock to the right, “service—” appears in the display.

5. Switch off the ignition. Only now is the service event reset.

How to Reset the Service Light on a Jeep

Instructions

Things You’ll Need
Wrench
Ignition key
OBDl or ll scanner

1. Disconnect your battery cables from the battery posts with a 6-pt. closed wrench in the size appropriate for the battery bolts. Remove the negative (black) cable first. Leave the battery disconnected for several minutes, according to Allpar.com. Reconnect, this time starting with the positive cable, and crank the engine. The code should be gone.

2. Crank the Jeep. Drive it forward, then backwards, and shut off. Repeat this procedure three times. The codes should clear on the fourth crank.

3. Use a OBDl or OBDll scan tool. Plug the tool into your Jeep’s ALDL (Assembly Line Diagnostic Link), a small, rectangular electrical port usually located under the dash. Turn the key to the “on” position. Scan the computer for codes and select the option to clear the codes.

4. Wait for the code to clear itself automatically. Once the component is fixed, the check engine light disappears after several successful ignitions. The code is then stored for a while. If the engine continues to start and run without a re-occurrence of the original problem, the code is wiped out.

Chevrolet Cobalt 2004-2010 Oil Service Light Reset

2005-2010

Turn the ignition to run (one position before starting engine).
Press the INFORMATION and RESET buttons on the DIC at the same time to enter the personalization menu.
Press the INFORMATION button to scroll through the menu until OIL LIFE RESET is displayed.
Press and hold the RESET button until the DIC display shows ACKNOWLEDGED. This will tell you the system has been reset.
Turn the ignition off and then start the engine to verify the indicator has been reset.