Service Reset:
1)Push-hold Trip Button (TB)
2)Turn key to position 1
3)Continue to hold (TB), the number 15A will show to the teft of the milage
4)Release (TB) for 3 sec and then hold (TB) again
5)In about 5-8 sec RST will show in the left corner
6)Release and then hold again 15000 will show, press and release
7)Car is now reset to the 15,000 service – (has completed 10,000 mile service) and will count down from 15,000.
1994-1995
Engine Oil Life Monitor
Turn the ignition to run (one position before starting engine).
Display the oil life index on the Driver Information System.
Hold the RESET button for 5 seconds. When a DIC message of RESET is displayed and the oil life index equals 100%, the reset is complete.
Turn the ignition off and then start the engine to verify the indicator has been reset.
Change Oil Soon
Turn the ignition to run (one position before starting engine).
Press OIL button and release.
Select OIL menu by pressing MODE button.
Press and hold the RESET button for 5 to 7 seconds.
Turn the ignition off and then start the engine to verify the indicator has been reset.
1996-1997
Turn the ignition to run (one position before starting engine).
Display the oil life index on the Driver Information System.
Hold the RESET button for 5 seconds.
Turn the ignition off and then start the engine to verify the indicator has been reset.
1998
Turn the ignition to run (one position before starting engine).
Press the TRIP button on the Driver Information System (DIC) switch to view various menu choices and stop on OIL LIFE REMAINING.
Press and hold the RESET button on the DIC switch for more than 5 seconds. The oil life will change to 100%. The engine oil life monitor is now reset.
Turn the ignition off and then start the engine to verify the indicator has been reset.
1999
Turn the ignition to run (one position before starting engine).
Press and hold the OIL RESET button in the IP storage compartment for at least 5 seconds, but no more than 60 seconds.
After 5 seconds, observe the CHANGE OIL SOON light flash 4 times before light turns off. This indicates that the engine oil life monitor system has reset.
Turn the ignition off and then start the engine to verify the indicator has been reset.
1982-1991
Turn the ignition to run (one position before starting engine).
The oil life index may be reset by pressing and holding the OIL and RESET buttons for approximately 5 seconds.
Turn the ignition off and then start the engine to verify the indicator has been reset.
1992-1993
Turn the ignition to run (one position before starting engine).
Press the TEST button and release.
Press the OIL button and release.
Press and hold the RESET button for approximately 7 seconds.
Turn the ignition off and then start the engine to verify the indicator has been reset.
1995
Turn the ignition to run (one position before starting engine).
Press the test button and release.
Press OIL button and release.
Press and hold the RESET button for 5 to 7 seconds.
Turn the ignition off and then start the engine to verify the indicator has been reset.
1996-1997
Turn the ignition to run (one position before starting engine).
Display the oil life index on the Driver Information System.
Hold the reset button for 5 seconds.
Turn the ignition off and then start the engine to verify the indicator has been reset.
1998
Turn the ignition to run (one position before starting engine).
Press the ENG button on the DIC control panel until the OIL LIFE percentage appears.
Press and hold the RESET button for more than 5 seconds. The word RESET appears. Then the message OIL LIFE 100% appears.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2001-2003
Turn the ignition to run (one position before starting engine).
Press the RIGHT arrow button on the DIC until OIL LIFE percentage is displayed.
Press RESET and hold for 5 seconds. OIL LIFE 100% will appear and then when the button is released OIL LIFE 100% will be displayed.
Turn the ignition off and then start the engine to verify the indicator has been reset.
Here’s how to do it yourself in no time works on a few different Jags….
Service Light Reset Instructions:
1 . Insert key into ignition.
2 . Press and hold the Reset switch (located on the Trip Computer Switchpack ).
3 . NOTE: The reset switch has to be released immediately after the ignition is switched ‘ON’. This is critical to enable the rest of the procedure.
Turn the key to Ignition position II and at the point of entering Ignition position II (i.e when a click is heard), instantaneously release the Reset switch.
4 . Wait one second.
5 . Press and hold the Trip switch (located on the end of the left-hand side stalk).
6 . Wait one second.
7 . Press and hold the Reset switch (whilst still holding the Trip switch).
8 . The cluster should display (within three seconds) the warning message ‘RESETTING SERVICE MODE’.
9 . Keep both buttons pressed until the warning message changes to ‘SERVICE MODE RESET’ (after ten seconds).
10 . Once the message is displayed the buttons may be released — sequence is now complete.
11 . If a Service Required message was displayed prior to the reset sequence, cycle the ignition to ‘Off’ and then back to Ignition position II and check that the message is no longer displayed.