Tag: push

Service oil reset Infiniti QX56

2004-2007
Turn the ignition to run (one position before starting engine).
Push the ěTRIPî button repeatedly to display “MAINTENANCE” and press the “ENTER” button.
Select “Engine Oil” and press the “ENTER” button.
Select “RESET” and press “ENTER” button.
Press “PREV” to return to previous menu.
Turn the ignition off and then start the engine to verify the indicator has been reset.

2008-2010
Turn the ignition on without starting the engine (press START/STOP) button.
Push the ěINFOî button on the control panel for the Vehicle Information screen.
Use arrow keys to scroll down to “Maintenance” and press “ENTER” button to select.
Select “Reminder 1” and press “ENTER” button.
Select “Reset Distance” and press “ENTER” button.
Press “Back” button to return to “Maintenance” menu and repeat procedure for “Reminder 2″… Turn the ignition off and then start the engine to verify the indicator has been reset.

Service oil reset Infiniti M Series

2003-2004
Turn the ignition to run (one position before starting engine).
Push the “INFO” button on the control panel for the Vehicle Information screen.
Choose “Maintenance” using the joystick and push the “ENTER” button.
Select “Engine Oil” and press “ENTER” button.
Select “Reset” and press “ENTER” button.
Press “PREV” button to return to “Maintenance” menu and repeat procedure for “Oil Filter”. Turn the ignition off and then start the engine to verify the indicator has been reset.
2006-2007
Turn the ignition to run (one position before starting engine).
Push the “INFO” button on the control panel for the Vehicle Information screen.
Use arrow keys to scroll down to “Maintenance” and press “ENTER” button to select.
Select “Engine Oil” and press “ENTER” button.
Select “Reset Distance” and press “ENTER” button.
Press “BACK” button to return to “Maintenance” menu and repeat procedure for “Oil Filter”. Turn the ignition off and then start the engine to verify the indicator has been reset.
2008-2010
Turn the ignition on without starting the engine (press START/STOP) button.
Push the “INFO” button on the control panel for the Vehicle Information screen.
Use arrow keys to scroll down to “Maintenance” and press “ENTER” button to select.
Select “Reminder 1” and press “ENTER” button.
Select “Reset Distance” and press “ENTER” button.
Press “Back” button to return to “Maintenance” menu and repeat procedure for “Reminder 2″… Turn the ignition off and then start the engine to verify the indicator has been reset.

Service oil reset Honda Prelude

1982-1989
Insert ignition key into slot below indicator flag at lower right corner of instrument cluster.
Push key in until indicator changes from red to green.
1990-1999
Insert ignition key into centre slot located on the front of the instrument cluster. When reset, the indicator changes to green.
2000-2002
Reset the coloured indicator by inserting your key in the slot beside the indicator.

Service oil reset Honda CRX

1984-1990
Insert ignition key into slot below indicator flag at lower right corner of instrument cluster.
Push key in until indicator changes from red to green.

How to replace the rear brake pads on my passat 2007?

solved the problem, i found a TSB explaing what to do when this happens, and than i found a realy good HOW TO.

Practicly you need to reset the hand brake cylinder by:

1. Disconect batery for 5 minutes (this means if your car is 2007> you will have to go to dealer so he can put the code for radio thru some GEKO system othervise you cant use the radio!)

2. Connect the batery.

3. Dont start the car only give contact (many lights go on )

4. pres and hold the brake while presing the hand brake 2 times on and 2 times off. (i waited 30 seconds betven “on” and “off” cause the manual i found wasnt very clear)

5. Than i pussehd the cylinder back with hands, (Be carful not to turn it!!!) only push it straight i did it by hand.

6. Put everything back, deleted the fault codes and started all over again like manual said on the previous post.

I did everything like it said but at the end i end up with P on the dash light up, than i only deleted the fault codes from controler 53 – Hand brake and it worked like a charm!