Service light reset on Peugeot Citroen inc 206 106 saxo

There’s no great “trade secret” as to how to reset the service indicator lamp on most Peugeot / Citroen, simply refer to pages in the Owner’s Handbook!

For reference of those interested in such matters, but who might not have access to an owner’s manual, this is the procedure to follow:

1) Ensure “ignition” key is turned off.
2) Depress and hold the odometer reset button whilst turning the “ignition” switch to the on position.
3) Keep the odometer reset button depressed for 10 seconds whilst the service display counts down from 10 to 0. When the count down reaches zero the spanner icon will vanish from the display and the service indicator will be reset.

Note 1: When reset, the service indicator is actually reset to 9,500 miles. The mileage that the car accumulates henceforth is subtracted from 9,500 miles, until 9,500 miles have elapsed at which point the service indicator icon will reappear inorder to warn the driver that the next service is imminent. Any mileage accumulated beyond 10,000 miles since the last reset will be indicated with a minus sign displayed infront of the mileage to indicate by how much a service is overdue.

Note 2: To the best of my knowledge, the above service light reset procedure applicable to most Peugeot cars, most Citroen cars and most Fiat cars with the exception of the Fiat Stilo. (Also applicable to car derrived vans from the above ranges).

How to Reset the “MAINT REQD” Light on Toyota Sienna

1. With the car started (ignition on), set the LCD odometer readout to total mileage (not trip A or B).
2.Turn the car off (ignition key to the OFF position).
3. Push in AND HOLD the button/knob that switches the odometer
4. Turn key to ON position without starting the car. You will notice the maintenance light blink and go out.
5. Release the odometer button/knob.
6. Turn key to OFF position.
That’s it! The “MAINT REQD” light has been reset to warn you to change your oil in another 5,000 or 7,500 miles or so.

Service reset VW Crafter 2.5 td

VW Crafter service reset Sitting in the drivers seat looking at the dash on the left hand side you have a M button and below it a 0 button these are the buttons you will need to use.

When i refer to the LCD this is the illuminated part in the middle that shows your mileage,service mileage and trip mileage.

Please read this fully first to get the jist of it as if you perform the actions too slow it wont work and you will have to start over.

1.Put on ignition

2.Wait for service mileage to revert to vehicle mileage

3.When it reverts to the vehicle mileage press and hold the 0 button until you hear a beep (can take up to 30 seconds)

4.As soon as you hear the beep press the M button repeatdly and you will see in the LCD display different reset’s the one you need to select is “reset 51” if you go past it just keep pressing the M button till it comes up again.

5.When the “reset 51” is displayed stop pressing the M button then press and hold the 0 button again until a number 2 is displayed in the LCD.

6.Release the 0 button and then press twice and it will say in the LCD reset done ,if it is not reset you will get a 30% power reduction after 2K miles

Service reset Sprinter 2007

Sprinter service reset Sitting in the drivers seat looking at the dash on the left hand side you have a M button and below it a 0 button these are the buttons you will need to use.

When i refer to the LCD this is the illuminated part in the middle that shows your mileage,service mileage and trip mileage.

Please read this fully first to get the jist of it as if you perform the actions too slow it wont work and you will have to start over.

1.Put on ignition

2.Wait for service mileage to revert to vehicle mileage

3.When it reverts to the vehicle mileage press and hold the 0 button until you hear a beep (can take up to 30 seconds)

4.As soon as you hear the beep press the M button repeatdly and you will see in the LCD display different reset’s the one you need to select is “reset 51” if you go past it just keep pressing the M button till it comes up again.

5.When the “reset 51” is displayed stop pressing the M button then press and hold the 0 button again until a number 2 is displayed in the LCD.

6.Release the 0 button and then press twice and it will say in the LCD reset done ,if it is not reset you will get a 30% power reduction after 2K miles

service light reset Ford Galaxy

With the ignition off, press the reset button under the mileage counter
Hold in reset button whilst turning the ignition on
After about 4 or 5 seconds (up to 30 seconds in some cases) the display should reset itself
Release the button and turn the ignition off
It may be necessary to repeat this process