Tag: ignition

Volvo 850-70 Service Light Reset

RESETTING 5000 MILE SERVICE LAMP ON 1994 + 1995 850

NOTE: This function is for the service reminder lamp, be sure you have performed the proper service such as changing the oil before resetting. If the check engine lamp is illuminated when the car is running, you’ll need to have the car looked at by the Volvo dealer for proper diagnosis.

1. Turn on the ignition to the KPII position so the warning lamps on the dash are illuminated. Do not start the car.

2. Open the bonnet of the car and locate Diagnostic test port (A) behind the driver side headlamp.

3. Remove the cover and pull the jumper wire out of the holder in the cover.

4. Insert the jumper into terminal #7, then press button 4 times, wait approximately 5 seconds and the red lamp should glow continuously. You are now in the data reset mode.

5. Press the button 1 time and wait approximately 5 seconds for the lamp to glow again then press the button 5 times. After about 5 seconds the lamp will illuminate again, press the button 1 time and you will see the lamp flash repeatedly for a couple of seconds indicating that the service lamp has been properly reset.

6. If a mistake is made, simply switch the ignition off and back on to reset and start over.

1996 Model (Some of them)
On these models the diagnostic socket is in front of the gear stick. Switch the ignition on. As you look at the speedometer on the dash, beneath it opposite the trip reset button is a rubber plug. Remove the plug and with a thin pointer such as a ball point pen, depress the pin. This will reset the service light.

1999 Model Service Lamp Reset Procedure

1. Press and hold trip odometer reset button

2. Turn ignition key to run position KPII (not the start position)

3. Wait 30 seconds or until service light begins blinking

4. Release Trip Odometer button

5. Turn ignition to off position

Reset oil change light on a 2008 dodge nitro

1. Turn the ignition key to ON but do not start the engine.
2. Slowly depress the accelerator to the floor and release it three times within 10 seconds.
3. Turn the ignition key to the OFF position.

2010 Dodge Grand Caravan how to reset oil light

To reset the oil change indicator system (after
performing the scheduled maintenance), refer to the
following procedure:

1. Turn the ignition switch to the ON position (Do not
start the engine).
2. Fully depress the accelerator pedal slowly three times
within 10 seconds.
3. Turn the ignition switch to the OFF/LOCK position.
NOTE: If the indicator message illuminates when you
start the vehicle, the oil change indicator system did not
reset. If necessary repeat this procedure.

Reset maintenance light on dodge sprinter

1. Put the key in the ignition and switch it on without starting the engine.
(Wait for LCD to return to the vehicle mileage)
2. Hold the “O” button down till you hear a beep (could take a while, 30 sec.)
3. Press the M button repeatedly and a number of reset menus will appear, (If you have used oil according to quality sheet 229.31 or 228/229.51 you can scroll to Reset.31 or Reset.51 respectively.) Select “reset 51”
4. Now, when appropriate oil type is selected press “O” for 6 seconds until ”2” is displayed.
5. Press “O” once again briefly and the ” reset done” message will confirm that the job is done.
6. Pull the Key out
FOR THE 2004 DODGE SPRINTER!

Turn the key to position 2 in the ignition lock and immediately press the button MI (km) twice.
Within 10 seconds, return the key to the 0 in the ignition lock.
Press and hold the button MI (km). Turn the key to position 2 in the ignition lock. Keep the button MI (km) pressed.
The maintenance indicator with the time/distance is shown.
After about 10 seconds, an acoustic signal will sound and the maintenance indicator is displayed with the new remaining time / distance .
Release the button MI (km)

Reset service light 2003 Bentley Continental GT

With the ignition key off, press and hold the trip button
while doing this, turn the ignition key to the on position
The driver’s instrument panel screen will now read “service reset.”
Now press the silver knurled knob on the right side of the steering wheel controls, this will confirm the operation.