Tag: engine

Turn Off an Oil Light on a 2005 KIA Spectra

Instructions

1. Pull the vehicle over to a safe area, if the light comes on while driving. If you are very close to a store that sells motor oil, stop there. Do not continue driving with the indicator light lit, as severe engine damage may occur.

2. Turn off the vehicle’s engine and open the hood. Locate the oil filler cap and oil dipstick on the top-front of the engine.

3. Check the engine oil level on the oil dipstick. If the engine oil is low, remove the oil cap and add oil until the oil level on the oil dipstick reaches the “Full” mark.

4. Replace the oil cap and restart the Kia. The oil light should turn off within a few seconds of starting the vehicle.

Reset oil change light on a 2008 dodge nitro

1. Turn the ignition key to ON but do not start the engine.
2. Slowly depress the accelerator to the floor and release it three times within 10 seconds.
3. Turn the ignition key to the OFF position.

Reset the SLK 230 for an Oil Change

The Mercedes-Benz SLK 230 features an engine oil-life tracking system as part of the car’s computer. The computer monitors driving habits and engine conditions to determine when the oil needs to be changed. The control panel displays a reminder when the car needs an oil change. In order for the computer system to work correctly to predict the next oil change, reset the light following an oil service.

1. Insert the key in the ignition. Turn the key to position “2.”

2. Press the adjust button twice within one second. The adjust button is located below the speedometer.

3. Turn the ignition off.

4. Press and hold the adjust button. Turn the ignition to position “2.”

5.Release the adjust button after a signal sounds and the service indicator resets visibly.

Reset Service Indicator of BMW 3 E46 Chassis

Turn key switch ON or when start engine, the instrument panel will display “OIL Service” or“INSPECTION” and left distance for several seconds. If “Service” or“ INSPECTION” are lit all the time and the left distance is next to “0”? it indicates that it needs oil service reset.

Reset by manual :
1. Press RESET button in the left of instrument panel.
2. Turn key ON and to ACC position.
3. Waiting for the instrument displays “OIL Service” or “INSPECTION” is flashed.
4 Release RESET button, then press five seconds, the screen will display RESR or RE is flashed. Release RESET button again and press again till the screen displays “25000km”. Now reset is completed.

When you find there is “-“symbol in front of the left distance number in the screen, and you can’t do reset with the above method, now you can use X-431 to reset oil service.

Oil service reset Tornado

1986-1988

Turn the ignition to run (one position before starting engine).
The oil life index may be reset by pressing and holding the ENGINE DATA and GAGE buttons until Oil Index 100 message appears in the information display panel.
Turn the ignition off and then start the engine to verify the indicator has been reset.

1989

Turn the ignition to run (one position before starting engine).
Press ENG DATA until oil life index is displayed.
Press ENG DATA and GAGE simultaneously until oil life index resets to 100.
Turn the ignition off and then start the engine to verify the indicator has been reset.

1990

Turn the ignition to run (one position before starting engine).
Press ENG DATA until oil life index is displayed.
Press RESET/ENTER until oil life index resets to 100.
Turn the ignition off and then start the engine to verify the indicator has been reset.

1991-1992

Without Visual Information Centre:
Turn the ignition to run (one position before starting engine).
Press OPTIONS until oil life index is displayed.
Press RESET/ENTER until oil life index resets to 100 (hold about 5 seconds).
Turn the ignition off and then start the engine to verify the indicator has been reset.
With Visual Information Centre:
Turn the ignition to run (one position before starting engine).
Press INFO key then OIL LIFE key to display oil life index.
Press RESET key until oil life index resets to 100.
Turn the ignition off and then start the engine to verify the indicator has been reset.