Tag: dash

Reset the service light on opel / vauxhall signum 04

Considering it’s made by a GM company, I would assume the standard practice here works there…

Turn key to on, but do not start…
Pump gas peddle three times…
Press and hold brake peddle till the service light blinks and then goes out…
Start the car to make sure the light was reset…

Or…

Turn to on…
Hold trip reset button…
Start car
keep holding trip reset till the light on the dash goes out…

Hopefully one of those works, but they’re just kinda the ‘try this’ until someone who knows chimes in.

Reset service notification on display at vw sharan 2001

with the ignition off

press and hold the miles reset button in on dash

now turn on ignition and start engine

‘service now’ should now be displayed

now turn the clock adjuster button either left or right and this should rest the service

noification.

Service reset VW Crafter 2.5 td

VW Crafter service reset Sitting in the drivers seat looking at the dash on the left hand side you have a M button and below it a 0 button these are the buttons you will need to use.

When i refer to the LCD this is the illuminated part in the middle that shows your mileage,service mileage and trip mileage.

Please read this fully first to get the jist of it as if you perform the actions too slow it wont work and you will have to start over.

1.Put on ignition

2.Wait for service mileage to revert to vehicle mileage

3.When it reverts to the vehicle mileage press and hold the 0 button until you hear a beep (can take up to 30 seconds)

4.As soon as you hear the beep press the M button repeatdly and you will see in the LCD display different reset’s the one you need to select is “reset 51” if you go past it just keep pressing the M button till it comes up again.

5.When the “reset 51” is displayed stop pressing the M button then press and hold the 0 button again until a number 2 is displayed in the LCD.

6.Release the 0 button and then press twice and it will say in the LCD reset done ,if it is not reset you will get a 30% power reduction after 2K miles

Service reset Sprinter 2007

Sprinter service reset Sitting in the drivers seat looking at the dash on the left hand side you have a M button and below it a 0 button these are the buttons you will need to use.

When i refer to the LCD this is the illuminated part in the middle that shows your mileage,service mileage and trip mileage.

Please read this fully first to get the jist of it as if you perform the actions too slow it wont work and you will have to start over.

1.Put on ignition

2.Wait for service mileage to revert to vehicle mileage

3.When it reverts to the vehicle mileage press and hold the 0 button until you hear a beep (can take up to 30 seconds)

4.As soon as you hear the beep press the M button repeatdly and you will see in the LCD display different reset’s the one you need to select is “reset 51” if you go past it just keep pressing the M button till it comes up again.

5.When the “reset 51” is displayed stop pressing the M button then press and hold the 0 button again until a number 2 is displayed in the LCD.

6.Release the 0 button and then press twice and it will say in the LCD reset done ,if it is not reset you will get a 30% power reduction after 2K miles

Reset Your Service Light Peugeot

If that spanner symbol has come up on your dashboard then it’s time your car was due a service. The symbol is just a periodic reminder, it doesn’t actually come up to denote a fault – the ‘check engine’ symbol does that.

If you service the car yourself and want to reset it or your garage has forgotten to reset it, you can do it yourself quite easily with the following simple steps:

This will work with the following models:

Peugeot 106 (1999 on)
Peugeot 206 (1998 on)
Peugeot 306 (1996 on)
Peugeot 307 (1996 on)
Peugeot 406 (1998 on)
Peugeot 607 (2000 on)
Peugeot 806 (1999 on)
Peugeot Expert (1999 on)
Peugeot 807 (2002 on)
Peugeot Partner (1999 on)
Peugeot Boxer (2002 on)

Procedure to Reset Peugeot Service Light as follows:

1. Switch the Ignition Off

2. Press and hold the tripmeter (mileage reset) button on the dash

3. Now switch the ignition to the ON position

4. Keep the button pressed for 10 seconds

5. The display will read ‘0’ and the service symbol will extinguish. Job done.