Tag: cluster

Oil service reset Saturn Astra

2008

Turn the ignition key to OFF.
Press the instrument panel cluster stem until the odometer is displayed.
Press and hold the cluster stem until the letters “InSP” are displayed.
Hold the cluster stem down and turn the ignition key to RUN (one position before starting engine).
The letters “InSP” in the instrument panel cluster display will flash.
Keep the cluster stem down for at least 20 seconds and then release the stem. If the letters “InSP” and the remaining mileage for the next oil change appear in the instrument panel cluster display, the system is properly reset. Turn the ignition off and then start the engine to verify the indicator has been reset.

2009

Turn the ignition key to LOCK/OFF.
Press the instrument panel cluster stem until the odometer is displayed, then release the stem.
Re-press and hold the cluster stem until the letters “InSP” are displayed.
Press and hold the brake pedal down, hold the cluster stem down, and turn the ignition key to RUN (one position before starting engine).
The letters “InSP” in the instrument panel cluster display will flash.
Keep the cluster stem down for at least 10 seconds and release the stem and the brake pedal when the message “new remaining mileage” is displayed. Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil service reset Chevrolet GMC Trucks Colorado/Canyon

2004

Turn the ignition to run (one position before starting engine).
Display OIL LIFE on the DIC by pressing the reset stem button.
Press and hold the reset stem. The oil life will change to 100% and a beep will sound.
Turn the ignition off and then start the engine to verify the indicator has been reset.

or

Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds.
Turn the ignition off and then start the engine to verify the indicator has been reset.

2005-2010

Turn the ignition to run (one position before starting engine).
Press and release the TRIP/RESET stem button in the DIC until the OIL LIFE message is displayed (located in the lower centre of instrument cluster).
Once the alternating OIL LIFE and RESET messages appear on the DIC display, press and hold the reset stem until several beeps sound. This confirms that the oil life system has been reset.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil service reset Land Rover Range Rover

2005-2009

Manual Reset Procedure:
Press and hold the trip reset button.
Turn the ignition switch on to the ignition position II (one position before starting engine).
If the SII (Service Indicator Interval) function is enabled the information display will flash ‘SERVICE’ for 5 seconds and then display ‘SERVICE’ constantly. If the SII function is not enabled the information display will show the normal odometer and trip information.
If the trip reset button is released within 10 seconds of entering the reset mode, the information display will show ‘DIST’. If the trip reset button is not released after 10 seconds the instrument cluster will exit the manual reset procedure.
If the oil service value is to be reset, press the trip reset button within 10 seconds for 5 seconds and then reset the oil service value, the display will then show ‘END’.
If the trip reset button is pressed for 5 seconds the display will exit the reset routine. If the trip reset button is not pressed for more than 10 seconds, then the information display will exit the reset routine. Turn the ignition off and then start the engine to verify the indicator has been reset.

Service oil reset Mercedes Benz S – Class

1997-1999
*Diagnostic Reset Tool Required
Turn key in steering lock to position 2.
Within 4 seconds press button (1) left of speedometer twice.
The present status for days or distance displays, within 10 seconds turn key in steering lock to position 0.
Press and hold button (1), while turning key in steering lock to position 2 again. The present status for days or distance displays once more.
Continue to hold button (1) for approximately 10 seconds until a signal sounds and the display shows 10 000 mils or 15 000km. Release button (1).

2000-2004
Turn on the ignition (standard display of the control system appears).
Press button (UP arrow) or (DOWN arrow) on the multifunction steering wheel until the FSS indicator with (Single Wrench) or (Double Wrench) and the service deadline appears in the multifunction display.
Press the reset knob to the right in the instrument cluster for about 2 seconds. This message appears in the multifunction display: “SERVICE INTERVAL? RESET WITH R BUTTON”.
To confirm hold down the reset button until you hear a signal. The service indicator now displays the reset interval.

Service oil reset Mercedes Benz G Class

2002
Turn key in steering lock to position 2.
Press either of the lower two system select buttons on left hand side of steering wheel (looks like 2 over lapping file folders) until the trip and main odometer display appears.
Press either of the top buttons on steering wheel (arrows) until the FSS indicator appears.
Press R button on the instrument cluster for 2-4 seconds.
The display reads “DO YOU WANT TO RESET SERVICE INTERVAL? CONFIRM BY PRESSING R”.
Press R button on the instrument cluster again and hold until signal sounds (about 10 seconds). Message now reads “SERVICE INTERVAL HAS BEEN RESET”.
2003
Turn on the ignition (standard display of the control system appears).
Press button (UP arrow) or (DOWN arrow) on the multifunction steering wheel until the FSS indicator appears in the multifunction display.
Press the reset knob for about 4 seconds. The message appears in the tachometer “DO YOU WANT TO RESET SERVICE INTERVAL? CONFIRM BY PRESSING R”.
To confirm, hold down the reset knob until you hear a signal. The service indicator now displays the reset interval.
2004
Turn on the ignition (standard display of the control system appears).
Press button (UP arrow) or (DOWN arrow) on the multifunction steering wheel until the FSS indicator appears in the multifunction display.
Press the reset knob for about 3 seconds. The message appears in the tachometer “SERVICE INTERVAL? RESET WITH R BUTTON FOR 3 SEC.”.
To confirm, hold down the reset knob until you hear a signal. The service indicator now displays the reset interval.