Polo 96-99
IN01 -inspection service
Switch ignition ON
Press and hold button (A left) under speedo
Switch ignition OFF
Release button
Press and release button A (left)
The letter “IN01” will appear in the odometer display of the speedometer.
Press clock minute button B until “—–” appears in the display
Press button A (left) to display “OEL”
Press button B to display “—–”
Switch ignition on until the letters “IN00” appear in the display
I have instructions for Oil service (OEL) and IN02 inspection service if this doesn’t work.
Most models of the Mercedes-Benz CLK 320 are equipped with a service reminder system that displays a notification light on the control panel when service is due. The onboard computer tracks driving conditions to determine when to illuminate the service reminder light. The service technician at the Mercedes-Benz dealer or garage will reset the service light for you when he performs regular maintenance on the car. If you do your own maintenance, you can turn the light off yourself.
1. Turn the ignition switch on. Do not start the engine.
2. Press the information menu button on the left of the steering wheel repeatedly until the total mileage is displayed.
3. Press the up- or down-arrow button on the left of the steering wheel until the service light is displayed.
4. Press and hold the reset button until a confirmation message appears on the display. The reset button is located to the left of the odometer.
5. Press and release the reset button to confirm the reset. The service light turns off.
Resetare calculator / computer din bordul masini auto VW Craft 2.5td 2007 , atunci cand apare eroarea de service (oil service sau inspection reset ) :
Pe bordul masini ( stai pe scaunul soferlui ) in partea stanga cum te uiti la bord sunt 2 butoane un buton M si sub acesta un buton 0 .
Puneti contactul masini ( fara a porni motorul) .
Asteptati pana pe display apare km .
Pe urma apasati butonul 0 pana apare un semnal sonor ( poate dura si 30 de secunde ).
De indata ce ati auzit semnalul sonor apsati repede butonul M pana cand pe display apar diferite erori dumneavoastra trebuie sa selectati “reset 51” , in caz ca treceti de aceasta eroare apsati butonul M pana ajunge din nou la acest mesaj pe display “reset 51” .
Cand apare pe display “reset 51” nu mai apsati butonul M , apsati butonul 0 si tinetil apasat pana pe display apre numarul 2 .
Dati drumul la butonul 0 si pe urma apsati acelasi buton de 2 ori iar pe display va aparea “reset done” (gata s-a resetat) .
VW Crafter service reset Sitting in the drivers seat looking at the dash on the left hand side you have a M button and below it a 0 button these are the buttons you will need to use.
When i refer to the LCD this is the illuminated part in the middle that shows your mileage,service mileage and trip mileage.
Please read this fully first to get the jist of it as if you perform the actions too slow it wont work and you will have to start over.
1.Put on ignition
2.Wait for service mileage to revert to vehicle mileage
3.When it reverts to the vehicle mileage press and hold the 0 button until you hear a beep (can take up to 30 seconds)
4.As soon as you hear the beep press the M button repeatdly and you will see in the LCD display different reset’s the one you need to select is “reset 51” if you go past it just keep pressing the M button till it comes up again.
5.When the “reset 51” is displayed stop pressing the M button then press and hold the 0 button again until a number 2 is displayed in the LCD.
6.Release the 0 button and then press twice and it will say in the LCD reset done ,if it is not reset you will get a 30% power reduction after 2K miles
Sprinter service reset Sitting in the drivers seat looking at the dash on the left hand side you have a M button and below it a 0 button these are the buttons you will need to use.
When i refer to the LCD this is the illuminated part in the middle that shows your mileage,service mileage and trip mileage.
Please read this fully first to get the jist of it as if you perform the actions too slow it wont work and you will have to start over.
1.Put on ignition
2.Wait for service mileage to revert to vehicle mileage
3.When it reverts to the vehicle mileage press and hold the 0 button until you hear a beep (can take up to 30 seconds)
4.As soon as you hear the beep press the M button repeatdly and you will see in the LCD display different reset’s the one you need to select is “reset 51” if you go past it just keep pressing the M button till it comes up again.
5.When the “reset 51” is displayed stop pressing the M button then press and hold the 0 button again until a number 2 is displayed in the LCD.
6.Release the 0 button and then press twice and it will say in the LCD reset done ,if it is not reset you will get a 30% power reduction after 2K miles
Recent Comments