2005
Turn ignition to (II) – do not start engine.
Press the SELECT/RESET button until the oil life displays.
Press and hold the SELECT/RESET button for 10 seconds, until MAINTENANCE RESET displays.
Press the SELECT/RESET button to select OK to reset the display.
Select RESET on the display and press the SELECT/RESET button.
Turn ignition off and then start the engine to verify the indicator has been reset.
2006-2010
Turn the ignition to (II) – do not start the engine.
Press the SEL/RESET button on the steering wheel repeatedly until engine oil life is displayed.
Press and hold the SEL/RESET button for more than 10 seconds. The remaining engine oil life reset mode will be shown on the multi information display.
Select RESET by pressing the INFO (▲/▼) button, then press the SEL/RESET button to reset the engine oil life display. The maintenance item code(s) will disappear, and the engine oil life will reset to 100.
Turn the ignition off and then start the engine to verify the indicator has been reset.
*Models equipped with the keyless access system have an engine start/stop button instead of an ignition switch. Pushing start/stop button once without starting engine is equivalent of ignition (II).
2007-2010
Turn the ignition to (II) – do not start the engine.
Press the SEL/RESET button on the steering wheel repeatedly until engine oil life is displayed.
Press and hold the SEL/RESET button for more than 10 seconds. The remaining engine oil life reset mode will be shown on the multi information display.
Select RESET by pressing the INFO (▲/▼) button, then press the SEL/RESET button to reset the engine oil life display. The maintenance item code(s) will disappear, and the engine oil life will reset to 100.
Turn the ignition off and then start the engine to verify the indicator has been reset.
*Models equipped with the keyless access system have an engine start/stop button instead of an ignition switch. Pushing start/stop button once without starting engine is equivalent of ignition (II).
2006-2010
Turn the ignition to (II) – do not start the engine.
Press the SEL/RESET button on the steering wheel until you see the engine oil life display.
Press and hold the SEL/RESET button on the steering wheel for more than 10 seconds. The remaining engine oil life reset mode will be shown on the multi information display.
Select RESET by pressing the INFO (▲/▼) button, then press the SEL/RESET button to reset the engine oil life display. The maintenance item code(s) will disappear, and the engine oil life will reset to 100.
Turn the ignition off and then start the engine to verify the indicator has been reset.
Turn the ignition to run (push START/STOP button once).
Press the (square) button, located on the instrument panel just behind the steering wheel to the left, to display the SETTINGS mode.
In the setting mode screen press (circle) button to move to MAINTENANCE.
Set a desired interval by pushing (circle) button to highlight ENGINE OIL and pressing (square) button The reset mode will open up and allow you to enter the desired distance.
Select RESET and select new time or distance.
Repeat step 3 for ENGINE OIL FILTER. Turn the ignition off and then start the engine to verify the indicator has been reset.
1. Park your car on a level surface. If you have a stick shift car make sure the car is in gear. Do not set the parking brake. Place blocks in front of the front tires so the car does not move while you are working on it.
2. Open the hood of your car and locate the master cylinder. If necessary, remove brake fluid until the level in the container is less than half full. A turkey baster is a good tool for this. Put the brake fluid in the plastic container and dispose of it the way you dispose of motor oil.
3. Raise the rear end of your car with your car jack. Remove the rear tire or wheel assembly.
4. Remove the parking brake cable from the back of the caliper. Use the pliers to remove the cable clip (restraining clip).
5. Use the socket wrench to remove the upper mounting bolt from the caliper. If the upper guide pin moves while you do this, use a back-up wrench to hold the upper guide pin.
6. Rotate the caliper downward, pivoting it on the lower caliper bolt. Remove the inner and outer brake pads from the caliper.
1. Turn the caliper piston clockwise to retract it into the caliper housing. Insert the new brake pads into the caliper.
2. Swing the caliper upward and into place. Apply a thin coat of thread locking compound to the bolt and use the socket wrench to tighten the bolt to 271 inch lb. (35 Nm).
3. Reattach the parking brake cable to the caliper.
4. Replace the tire wheel assembly. Lower the car to the ground.
5. Pump the brake pedal a few times to seat the brake pads. Do this before trying to move your car.
6. Add fluid to the master cylinder container to replace any you removed before you removed the old brake pads.
7. Season the brake pads by making only gentle stops when you are driving for the first week after you install the new brake pads. Try not to do any hard stopping when you are seasoning the brakes.