The Service Reminder Indicator (SRI) is fitted to all 2000 EuroVans It stores two sets of information: Oil Change and Inspection Service. Here is the method to manually reset the SRI after performing a service:
Switch ignition OFF.
Press and hold down the trip odometer reset button (at the lower right of the instrument cluster).
Switch ignition ON and release the trip odometer reset button. It is not necessary to start the engine; merely turn the key until the ignition is ON.
The trip mileage area now displays “Service OIL”.
If trip odometer reset button is now pressed again, the display turns to “Service INSP”. Pressing the button again will cycle the display back to “Service OIL”.
When the reminder that needs to be reset (either OIL or INSP) is displayed, turn button for setting the clock (at lower left of instrument cluster) to the right. The display changes to “Service —-“. That reminder is now reset.
The second reminder is unaffected unless it is displayed by pressing trip odometer reset button and the clock button is turned right again.
Switch ignition OFF and back ON to resume normal display.
VW Crafter service reset Sitting in the drivers seat looking at the dash on the left hand side you have a M button and below it a 0 button these are the buttons you will need to use.
When i refer to the LCD this is the illuminated part in the middle that shows your mileage,service mileage and trip mileage.
Please read this fully first to get the jist of it as if you perform the actions too slow it wont work and you will have to start over.
1.Put on ignition
2.Wait for service mileage to revert to vehicle mileage
3.When it reverts to the vehicle mileage press and hold the 0 button until you hear a beep (can take up to 30 seconds)
4.As soon as you hear the beep press the M button repeatdly and you will see in the LCD display different reset’s the one you need to select is “reset 51” if you go past it just keep pressing the M button till it comes up again.
5.When the “reset 51” is displayed stop pressing the M button then press and hold the 0 button again until a number 2 is displayed in the LCD.
6.Release the 0 button and then press twice and it will say in the LCD reset done ,if it is not reset you will get a 30% power reduction after 2K miles
Sprinter service reset Sitting in the drivers seat looking at the dash on the left hand side you have a M button and below it a 0 button these are the buttons you will need to use.
When i refer to the LCD this is the illuminated part in the middle that shows your mileage,service mileage and trip mileage.
Please read this fully first to get the jist of it as if you perform the actions too slow it wont work and you will have to start over.
1.Put on ignition
2.Wait for service mileage to revert to vehicle mileage
3.When it reverts to the vehicle mileage press and hold the 0 button until you hear a beep (can take up to 30 seconds)
4.As soon as you hear the beep press the M button repeatdly and you will see in the LCD display different reset’s the one you need to select is “reset 51” if you go past it just keep pressing the M button till it comes up again.
5.When the “reset 51” is displayed stop pressing the M button then press and hold the 0 button again until a number 2 is displayed in the LCD.
6.Release the 0 button and then press twice and it will say in the LCD reset done ,if it is not reset you will get a 30% power reduction after 2K miles
Volvo 1999-2000 – S / V / C70 Models
Press and Hold odometer reset button
Turn ignition switch to “run” position
After SRL flashes, release odometer reset button
Turn ignition off
Turn ignition back on to confirm reset
Volvo 1998 – S80 Models
Turn ignition switch to position 1
Press and hold the odometer reset button
Turn ignition switch to position 2
Wait until service light blinks and then release odometer button
Volvo 1999-2000 – S80 Models
Turn ignition switch to position 1
Press and hold “day counter reset button”
Turn ignition switch to position 2
Continue holding day counter for approx. 10 seconds
After SRL flashes, release day counter button
Should hear “beep-beep” to confirm command accepted
Volvo 2001 – XC 70 Models
The following steps must be completed with no longer than 5 seconds between each step:
Make sure the trip meter is in T-1
Turn ignition key to position 1
Press and hold trip meter button until zero is shown
While still holding the trip meter, turn key to position 2
When original trip mileage returns, release the trip reset button
Turn key to off