Turn the car on. Wait about a minute for the computer to get to normal.
press and hold the travel mile reset button. Hold it untill an ! in a triangle appears. then your maintanance info will pop up. select the item to reset. and tap the side button on the wand atached to the stearing wheel. this button is what you use to browse through your computer. press the button once it will say “reset” press and hold it the second time and it will say reset, hold for 5 seconds or so and it will show a check mark next to “reset” confirming it has reset.
Here’s how to do it yourself in no time works on a few different Jags….
Service Light Reset Instructions:
1 . Insert key into ignition.
2 . Press and hold the Reset switch (located on the Trip Computer Switchpack ).
3 . NOTE: The reset switch has to be released immediately after the ignition is switched ‘ON’. This is critical to enable the rest of the procedure.
Turn the key to Ignition position II and at the point of entering Ignition position II (i.e when a click is heard), instantaneously release the Reset switch.
4 . Wait one second.
5 . Press and hold the Trip switch (located on the end of the left-hand side stalk).
6 . Wait one second.
7 . Press and hold the Reset switch (whilst still holding the Trip switch).
8 . The cluster should display (within three seconds) the warning message ‘RESETTING SERVICE MODE’.
9 . Keep both buttons pressed until the warning message changes to ‘SERVICE MODE RESET’ (after ten seconds).
10 . Once the message is displayed the buttons may be released — sequence is now complete.
11 . If a Service Required message was displayed prior to the reset sequence, cycle the ignition to ‘Off’ and then back to Ignition position II and check that the message is no longer displayed.
1999-2003
Turn the ignition to run (one position before starting engine).
Press the RESET button (in fuse panel block inside driver side door)and release. The CHANGE OIL indicator will start flashing.
Press and hold the RESET button until audible chime is heard and then release.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2004-2005
Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds. The reset is complete when you hear the chimes and the CHANGE OIL light goes out.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2002
Turn key in steering lock to position 2.
Press either of the lower two system select buttons on left hand side of steering wheel (looks like 2 over lapping file folders) until the trip and main odometer display appears.
Press either of the top buttons on steering wheel (arrows) until the FSS indicator appears.
Press R button on the instrument cluster for 2-4 seconds.
The display reads “DO YOU WANT TO RESET SERVICE INTERVAL? CONFIRM BY PRESSING R”.
Press R button on the instrument cluster again and hold until signal sounds (about 10 seconds). Message now reads “SERVICE INTERVAL HAS BEEN RESET”.
2003
Turn on the ignition (standard display of the control system appears).
Press button (UP arrow) or (DOWN arrow) on the multifunction steering wheel until the FSS indicator appears in the multifunction display.
Press the reset knob for about 4 seconds. The message appears in the tachometer “DO YOU WANT TO RESET SERVICE INTERVAL? CONFIRM BY PRESSING R”.
To confirm, hold down the reset knob until you hear a signal. The service indicator now displays the reset interval.
2004
Turn on the ignition (standard display of the control system appears).
Press button (UP arrow) or (DOWN arrow) on the multifunction steering wheel until the FSS indicator appears in the multifunction display.
Press the reset knob for about 3 seconds. The message appears in the tachometer “SERVICE INTERVAL? RESET WITH R BUTTON FOR 3 SEC.”.
To confirm, hold down the reset knob until you hear a signal. The service indicator now displays the reset interval.
1997-2000
*Diagnostic Reset Tool Required (please refer to TOOLS page)
Manual Reset:
Turn key in steering lock to position 2.
Within 4 seconds press 0 button twice.
The present status for days or distance displays, within 10 seconds turn the electroninc key in steering lock to position 0.
Press and hold 0 button while turning electronic key in steering loack to position 2 again. The present status for days or distance displays once more. Continue to hold 0 button for approximately 10 seconds until a signal sounds and the display shows 10 000 (15000KM) for approximately 10 seconds.
Release 0 button, the status is reset.
2001-2002
*Diagnostic Reset Tool Required (please refer to TOOLS page)
Manual Reset:
Turn key in steering lock to position 2.
To call up the trip odometer and main odometer, press either of lower two buttons on left hand side of steering wheel (system select – looks like file folder) until the display appears.
Press either of the top buttons on steering wheel (arrows) until the FSS indicator appears.
Press R button on the instrument cluster for 2-4 seconds.
The display reads “DO YOU WANT TO RESET SERVICE INTERVAL? CONFIRM BY PRESSING R”
Press R button on the instrument cluster again and hold until signal sounds. The message “SERVICE INTERVAL HAS BEEN RESET” appears in the multifunction display.
2003-2004
Turn on the ignition (standard display of the control system appears).
Press button (UP arrow) or (DOWN arrow) on the multifunction steering wheel until the FSS indicator appears in the display.
Press the reset knob for about 5 seconds until the SERVICE MENU appears in the multifunction display.
Select the CONFIRMATION menu with the (+) or (-) button.
Press the menu button (looks like file 2 over lapping file folders).
The service indicator now displays the CONFIRMATION menu. The selection marker is on CONFIRM. Press the menu button (looks like 2 over lapping file folders). The service indicator now displays the CONFIRM menu. The selection marker is on STANDARD OIL.
Press the menu button (looks like 2 over lapping file folders). The words SERVICE CONFIRMED appear in the multifunction display. The service indicator is now reset.
Press the menu button on the multifunction steering wheel until the standard display appears in the multifunction display.