Reset service light indicator Renault Safrane. How to reset maintenance light, reset oil service light. Can be made manually by use button on car dash board.
Reset service light indicator Renault Safrane. It was built in years: 1992, 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000.
1. The reset button is located on the bottom right hand side of the Rev counter on the instrument cluster.
2. Turn ON the ignition, do not start the vehicle.
3. Push reset button until Spanner warning light symbol will start flash.
4. Keep button depressed until Spanner warning light symbol stops flashing and remains illuminated.
5. Indicator shows appropriate service interval.
6. Release reset button.
7. Turn OFF the ignition and then start your Renault Sfrane to see if spanner warning light has been reset.
Note. Some vehicles are fitted with a SERV lamp, this is not a service interval indicator lamp, it is a malfunction indicator lamp (MIL).
2007-2012
1. Turn the ignition to position 1. (close all doors
2. Press the system selection button (3 located on the lower left of the steering wheel) repeatedly until the kilometer or temperature reading is shown in the multi information display.)
3. Press the TRIP reset button (center button on instrument panel) quickly 3 times. An audible beep will be heard followed by the battery voltage displayed.
4. Press the scoll forward/back button (left side of steering wheel) to highlight the “”Service menu””.”
5. Use the +/- buttons to select “”Confirmation”” menu. Press the system select button to confirm. The menu item “”Complete service”” is highlighted.”
6. Press the system selection button to confirm. “”Service confirmed”” appears.”
7. Use the scroll forward/back button to exit the menu.
8. Turn the ignition off and then start the engine to verify the indicator has been reset.
2006-2012
1. Turn the ignition to position 1. (close all doors
2. Press the system selection button (3 located on the lower left of the steering wheel) repeatedly until the kilometer or temperature reading is shown in the multi information display.)
3. Press the TRIP reset button (center button on instrument panel) quickly 3 times. An audible beep will be heard followed by the battery voltage displayed.
4. Press the scoll forward/back button (left side of steering wheel) to highlight the “”Service menu””.”
5. Use the +/- buttons to select “”Confirmation”” menu. Press the system select button to confirm. The menu item “”Complete service”” is highlighted.”
6. Press the system selection button to confirm. “”Service confirmed”” appears.”
7. Use the scroll forward/back button to exit the menu.
8. Turn the ignition off and then start the engine to verify the indicator has been reset.
1988-2000.5
BMW recommends the use of a reset tool.
2000-2005
BMW recommends the use of a reset tool.
Manual Reset
1. Turn off the ignition.
2. Press and hold the TRIP ODOMETER button in the instrument cluster and turn the ignition to Accessory 1 – do not start the engine.
3. Keep the button pressed for 5 seconds until OIL SERVICE RESET (RE) or INSPECTION RESET (RE) appears in the display. Then release the button.
4. Press and hold the button again for 5 seconds until RE or RESET flashes in the display. Then release the button.
5. With the display flashing
6. Turn the ignition off and start the engine to verify the indicator has been reset.
2004-2005
1. Turn ignition on but do not start engine.
2. Press the RESET button on the top left side of the instrument cluster for 10 seconds to display a four (4) line menu in the speedometer.
3. Press the RESET button or LOWER AXIAL (FAS) button on the turn signal/high beam switch to scroll through the menu.
4. Select ENGINE OIL and press the RESET button for a few seconds to display a two (2) line menu in the tachometer.
5. Press the RESET (or AXIAL) button to select the SERVICE AND MAINTENANCE.
6. Press the RESET button again for a few seconds.
7. Turn the ignition off and start the engine to verify the indicator has been reset.
2006-2012
BMW recommends the use of a reset tool.
Manual Reset
1. Turn ignition to Terminal 15 which is one turn of the key or one press of the START/STOP button.
2. Press and hold the Instrument Cluster Set/Reset button for 10 seconds.
3. The upper display in the Instrument Cluster will be illuminated with a Service Item. The lower display in the Instrument Cluster will indicate the remaining time or mileage left for that Service Item. Pressing the button repeatedly will allow the display to scroll through all of the Condition Based Service Items.
4. Press and hold the Instrument Cluster Set/Reset button again and the lower display screen will indicate “”OK”” or “”DUE””.”
5. Pressing the Instrument Cluster Set/Reset button again will allow the “”RESET”” to appear in the lower window for that service. Releasing and reapplying the button one more time will reset the service displayed in the upper window only. ”
6. Turn the ignition off and start the engine to verify the indicator has been reset.
2007-2011
1. Turn the ignition to run (one position before starting engine).
2. Select trip metre A reading by using the trip metre button and then turn the ignition off.
3. While pressing the trip meter reset button
4. Continue to press and hold the button until the trip meter displays “”000000″”.”
5. Turn the ignition off and then start the engine to verify the indicator has been reset.
2012
1. Turn the ignition to run (one position before starting engine).
2. Press the MODE switch knob on the upper right side of the combination meter until “”TRIP A”” is shown and then turn the ignition off.”
3. While pressing the trip meter reset button
4. After the reset procedure is complete
5. Turn the ignition off and then start the engine to verify the indicator has been reset.