2006-2012
1. Turn ignition to Terminal 15 which is one turn of the key or one press of the START/STOP button.
2. Press and hold the trip odometer reset button for approximately 10 seconds until the first service job appears in the display.
3. The upper display in the Instrument Cluster will be illuminated with a Service Item (example: An oil can is the designation for Oil Service). The lower display in the Instrument Cluster will indicate the remaining time or mileage left for that Service Item (example: 14000). Press the on-board computer button repeatedly (located on the direction indicator/main-beam switch) to scroll through all of the Condition Based Service Items.
4. Press and hold the on-board computer button on the direction indicator/main-beam switch until “”RESET”” appears in the lower display.”
5. Pressing the on-board computer button again resets the service shown in the upper display. Repeat the procedure for each additional service which is to be reset.
6. Turn the ignition off and start the engine to verify the indicator has been reset.
2009-2012
“Audi recommends the use of a reset tool. *Depening on model
2000-2004
*Diagnostic Reset Tool Required
Manual Reset using DIS and Reset Knobs:
1. Turn off the ignition
2. Locate the Driver Information System (DIS) in the instrument panel.
3. Do the following to display the SERVICE! message in the display.
i) Press and hold the right RESET knob.
ii) Turn on the ignition – do not start the engine.
iii) Release the knob.
4. Do the following to display the next service interval (SERVICE IN ##MI)
i) Press and hold the right RESET knob.
ii) Release the knob.
5. Turn off the ignition.
6. Start the engine and verify indicator has been reset.
Manual Reset for 2000 only:
1. Turn off the ignition.
2. Press and hold the TRIP RECORDER reset button on the instrument cluster and turn on the ignition.
3. Release the button. The display will show SERVICE IN —MI or SERVICE.
4. Within 5 seconds
5. Turn off the ignition.
6. Start the engine and verify indicator has been reset.
2005-2007
1. Turn off the ignition.
2. Press and hold the button to the right of the LCD display in the instrument cluster.
3.Turn the ignition on (do not start the engine); the message “”SERVICE”” appears. Release button.”
4. Within 5 seconds
5. Turn off the ignition.
6. Start the engine and verify indicator has been reset.
2008-2012
“Audi recommends the use of a reset tool. *Depening on model
2001-2005
Manual Reset using DIS and Reset Knobs:
1. Turn off the ignition
2. Locate the Driver Information System (DIS) in the instrument panel.
3. Locate the reset buttons (WRENCH button and 0
4. Do the following to display the SERVICE! Message in the DIS:
i) Press and hold the Wrench button.
ii) Turn on the ignition – do not start the engine.
iii) Release the WRENCH button.
5. Do the following to display the next service interval (SERVICE in ##MI)
i) Press and hold the 0
ii) Release the 0
6. Turn off the ignition.
7. Start the engine and verify indicator has been reset.
Manual Reset using DIS and Reset Knobs:
1. Turn off the ignition
2. Locate the Driver Information System (DIS) in the instrument panel.
3. Do the following to display the SERVICE! message in the display.
i) Press and hold the right RESET knob.
ii) Turn on the ignition – do not start the engine.
iii) Release the knob.
4. Do the following to display the next service interval (SERVICE IN ##MI)
i) Press and hold the right RESET knob.
ii) Release the knob.
5. Turn off the ignition.
6. Start the engine and verify indicator has been reset.
2000-2003
BMW recommends the use of a reset tool.
Manual Reset
1. Turn off the ignition.
2. Press and hold the TRIP ODOMETER button in the instrument cluster and turn the ignition to Accessory.
3. Keep the button pressed for 5 seconds until OIL SERVICE RESET (RE) or INSPECTION RESET (RE) appears in the display. Then release the button.
4. Press and hold the button again for 5 seconds until RE or RESET flashes in the display. Then release the button.
5. With the display flashing
6. Turn the ignition off and start the engine to verify the indicator has been reset.