2006-2009
Turn the ignition to run (one position before starting engine).
When the TRIP button is pressed, the following modes will display on the screen: Warning message (if any) TRIP1 > TRIP 2 > FUEL ECONOMY > MAINTENANCE > AUDIO OR OFF > TRIP
Select MAINTENANCE and then select the Engine Oil key using the joystick and press the ENTER button to display the screen to change the maintenance interval/RESET.
To return to the previous display after the MAINTENANCE NOTICE screen is displayed, press the BACK button.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2005-2006
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the ODO/TRIP knob then the turn ignition off.
Hold down ODO/TRIP knob while turning the ignition key to the run position (one position before starting engine).
Hold down the knob until the light goes off. Before the light goes off, it illuminates
3 seconds, flashes for 2 seconds and illuminates for 1 second. If the system fails to reset, the light will remain flashing. In this case, return to step 1 and try again.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2007
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the ODO/TRIP knob then the turn ignition off.
Hold down ODO/TRIP knob while turning the ignition key to the run position (one position before starting engine) for longer than 7 seconds. While doing this operation, the “engine oil replacement” reminder light goes off. If the system fails to reset, the light will remain flashing. In this case, return to step 1 and try again.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2008-2010
Turn the engine on by holding the START/STOP switch. Use the trip meter switch to bring up the trip meter A reading. Turn the ignition off.
While pressing the trip meter reset button, set the engine switch to run (push START/ STOP button once) and continue to press and hold the knob until the multi information display indicates that the reset is complete.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2004-2006
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the trip meter reset knob then the turn ignition off.
Hold down the trip meter reset knob while turning the ignition key to the run position (one position before starting engine).
Hold down the knob until the light goes off. Before the light goes off, it illuminates 3 seconds, flashes for 2 seconds and illuminates for 1 second. If the system fails to reset, the light will remain flashing. In this case, return to step 1 and try again.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2007-2009
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the trip meter reset knob then the turn ignition off.
Hold down the trip meter reset knob while turning the ignition key to the run position (one position before starting engine).
Keep pressing the knob until the ěMAINT REQDî light goes off. If the light continues flashing, return to step 1 and try again.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2010
Turn the ignition to run – engine off (push START/STOP button once).
Press the Menu switch to change the multi-information display to blank. Turn the engine off.
While pressing the ODO/TRIP button, set the ěENGINE START STOP” switch to run – engine off (push START/STOP button once).
Keep pushing the ěODO/TRIPî switch for more than 7 seconds. While doing this operation, the master warning light comes on, a warning tone sounds and the “RESETTING OIL MAINTENANCE DATA” message appears to inform you that light has been reset. After 5 seconds, the system reset is completed.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2004-2007
Turn the ignition to run (one position before starting engine).
Push the ěTRIPî button repeatedly to display “MAINTENANCE” and press the “ENTER” button.
Select “Engine Oil” and press the “ENTER” button.
Select “RESET” and press “ENTER” button.
Press “PREV” to return to previous menu.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2008-2010
Turn the ignition on without starting the engine (press START/STOP) button.
Push the ěINFOî button on the control panel for the Vehicle Information screen.
Use arrow keys to scroll down to “Maintenance” and press “ENTER” button to select.
Select “Reminder 1” and press “ENTER” button.
Select “Reset Distance” and press “ENTER” button.
Press “Back” button to return to “Maintenance” menu and repeat procedure for “Reminder 2″… Turn the ignition off and then start the engine to verify the indicator has been reset.
2003-2004
Turn the ignition to run (one position before starting engine).
Push the “INFO” button on the control panel for the Vehicle Information screen.
Choose “Maintenance” using the joystick and push the “ENTER” button.
Select “Engine Oil” and press “ENTER” button.
Select “Reset” and press “ENTER” button.
Press “PREV” button to return to “Maintenance” menu and repeat procedure for “Oil Filter”. Turn the ignition off and then start the engine to verify the indicator has been reset.
2006-2007
Turn the ignition to run (one position before starting engine).
Push the “INFO” button on the control panel for the Vehicle Information screen.
Use arrow keys to scroll down to “Maintenance” and press “ENTER” button to select.
Select “Engine Oil” and press “ENTER” button.
Select “Reset Distance” and press “ENTER” button.
Press “BACK” button to return to “Maintenance” menu and repeat procedure for “Oil Filter”. Turn the ignition off and then start the engine to verify the indicator has been reset.
2008-2010
Turn the ignition on without starting the engine (press START/STOP) button.
Push the “INFO” button on the control panel for the Vehicle Information screen.
Use arrow keys to scroll down to “Maintenance” and press “ENTER” button to select.
Select “Reminder 1” and press “ENTER” button.
Select “Reset Distance” and press “ENTER” button.
Press “Back” button to return to “Maintenance” menu and repeat procedure for “Reminder 2″… Turn the ignition off and then start the engine to verify the indicator has been reset.