Find how to reset any maintenance light or reset oil life after an oil change for all makes and models.

panel

Oil service reset Alero

1999-2003

Turn the ignition to run (one position before starting engine).
Push the RESET button located in the drivers instrument panel fuse block. The CHANGE OIL light will start to flash.
Press and hold the RESET button again. The reset is complete when you hear the chimes and the CHANGE OIL light goes out.
Turn the ignition off and then start the engine to verify the indicator has been reset.

2004

Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds. The reset is complete when the chimes sound and the CHANGE OIL lamp goes out. If the lamp stays on and and no chime is heard, repeat the reset procedure.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil light reset Jeep Renegade Concept

Many Jeep vehicles track the intervals between oil changes to alert the driver when the next oil change is needed. A light illuminates on the control panel when the internal system determines it is time for an oil change. Most Jeep mechanics reset the oil light as part of the oil change service. If you change the oil in your Jeep yourself, you can manually reset the oil light. Resetting the oil light after an oil change allows the system to accurately track the time until the next oil change is needed. The procedures described in this article apply to 2010 Jeep models.

Instructions

1.Turn the ignition switch to the “ON” position. Do not start the engine.

2.Press the accelerator pedal completely to the floor slowly three times within a 10-second span.

3.Turn the ignition switch to the “OFF” position.

4.Turn the ignition switch to the “ON” position again. The oil light should be off. If the oil light is still illuminated, repeat the previous steps.

Oil service reset Saturn Astra

2008

Turn the ignition key to OFF.
Press the instrument panel cluster stem until the odometer is displayed.
Press and hold the cluster stem until the letters “InSP” are displayed.
Hold the cluster stem down and turn the ignition key to RUN (one position before starting engine).
The letters “InSP” in the instrument panel cluster display will flash.
Keep the cluster stem down for at least 20 seconds and then release the stem. If the letters “InSP” and the remaining mileage for the next oil change appear in the instrument panel cluster display, the system is properly reset. Turn the ignition off and then start the engine to verify the indicator has been reset.

2009

Turn the ignition key to LOCK/OFF.
Press the instrument panel cluster stem until the odometer is displayed, then release the stem.
Re-press and hold the cluster stem until the letters “InSP” are displayed.
Press and hold the brake pedal down, hold the cluster stem down, and turn the ignition key to RUN (one position before starting engine).
The letters “InSP” in the instrument panel cluster display will flash.
Keep the cluster stem down for at least 10 seconds and release the stem and the brake pedal when the message “new remaining mileage” is displayed. Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil service reset Pontiac Grand Am

1999-2003

Turn the ignition to run (one position before starting engine).
Press the RESET button (in fuse panel block inside driver side door)and release. The CHANGE OIL indicator will start flashing.
Press and hold the RESET button until audible chime is heard and then release.
Turn the ignition off and then start the engine to verify the indicator has been reset.

2004-2005

Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds. The reset is complete when you hear the chimes and the CHANGE OIL light goes out.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil service reset Pontiac Firebird

1998

Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds. The Change Oil message flashes for 5 seconds when reset.
Turn the ignition off and then start the engine to verify the indicator has been reset.

1999-2002

Turn the ignition to run (one position before starting engine).
Press the TRIP/OIL RESET button on the instrument panel for 12 seconds. The CHANGE OIL light will start to flash to confirm that the system is reset when the flashing stops the system is reset.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Categories





Copyright © 2013. All Rights Reserved.