2008
Turn the ignition key to OFF.
Press the instrument panel cluster stem until the odometer is displayed.
Press and hold the cluster stem until the letters “InSP” are displayed.
Hold the cluster stem down and turn the ignition key to RUN (one position before starting engine).
The letters “InSP” in the instrument panel cluster display will flash.
Keep the cluster stem down for at least 20 seconds and then release the stem. If the letters “InSP” and the remaining mileage for the next oil change appear in the instrument panel cluster display, the system is properly reset. Turn the ignition off and then start the engine to verify the indicator has been reset.
2009
Turn the ignition key to LOCK/OFF.
Press the instrument panel cluster stem until the odometer is displayed, then release the stem.
Re-press and hold the cluster stem until the letters “InSP” are displayed.
Press and hold the brake pedal down, hold the cluster stem down, and turn the ignition key to RUN (one position before starting engine).
The letters “InSP” in the instrument panel cluster display will flash.
Keep the cluster stem down for at least 10 seconds and release the stem and the brake pedal when the message “new remaining mileage” is displayed. Turn the ignition off and then start the engine to verify the indicator has been reset.
2004-2008
Turn the ignition to run (one position before starting engine).
Within one second press the knob/button twice.
The present status for days or distance is displayed. Within 10 seconds turn the key to OFF/LOCK.
Press and hold the knob/button, while turning the distance is displayed once more. Continue to hold the knob/button. After 10 seconds, a signal sounds and the display shows 7,000 mi or 11000km for 10 seconds.
Release the knob/button.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2006-2008
Turn the ignition to run (one position before starting engine).
When you turn the ignition key run, the system start-up warning is displayed on the screen. Read the the warning and select the OK key by pressing the ENTER button.
When the TRIP button is pressed, the following modes will display on the screen: Warning message (if any) TRIP1 > TRIP 2 > FUEL ECONOMY > MAINTENANCE > AUDIO OR OFF > TRIP 1
Select MAINTENANCE and then select the Engine Oil key using the joystick and press the ENTER button to display the screen to change the maintenance interval/RESET.
To return to the previous display after the MAINTENANCE NOTICE screen is displayed, press the BACK button.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2009-2010
Turn the ignition to run (push START/STOP button once).
Press the (square) button, located on the instrument panel just behind the steering wheel to the left, to display the SETTINGS mode.
In the setting mode screen press (circle) button to move to MAINTENANCE.
Set a desired interval by pushing (circle) button to highlight ENGINE OIL and pressing (square) button The reset mode will open up and allow you to enter the desired distance.
Select RESET and select new time or distance.
Repeat step 3 for ENGINE OIL FILTER. Turn the ignition off and then start the engine to verify the indicator has been reset.
2006-2010
Turn the ignition to run (one position before starting engine).
When the TRIP button is pressed, the following modes will display on the screen: Warning message (if any) TRIP1 > TRIP 2 > FUEL ECONOMY > MAINTENANCE > AUDIO OR OFF > TRIP
Select MAINTENANCE and then select the Engine Oil key using the joystick and press the ENTER button to display the screen to change the maintenance interval/RESET.
To return to the previous display after the MAINTENANCE NOTICE screen is displayed, press the BACK button.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2006-2009
Turn the ignition to run (one position before starting engine).
When the TRIP button is pressed, the following modes will display on the screen: Warning message (if any) TRIP1 > TRIP 2 > FUEL ECONOMY > MAINTENANCE > AUDIO OR OFF > TRIP
Select MAINTENANCE and then select the Engine Oil key using the joystick and press the ENTER button to display the screen to change the maintenance interval/RESET.
To return to the previous display after the MAINTENANCE NOTICE screen is displayed, press the BACK button.
Turn the ignition off and then start the engine to verify the indicator has been reset.