2006-2008
Turn the ignition to run (one position before starting engine).
When you turn the ignition key run, the system start-up warning is displayed on the screen. Read the the warning and select the OK key by pressing the ENTER button.
When the TRIP button is pressed, the following modes will display on the screen: Warning message (if any) TRIP1 > TRIP 2 > FUEL ECONOMY > MAINTENANCE > AUDIO OR OFF > TRIP 1
Select MAINTENANCE and then select the Engine Oil key using the joystick and press the ENTER button to display the screen to change the maintenance interval/RESET.
To return to the previous display after the MAINTENANCE NOTICE screen is displayed, press the BACK button.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2009-2010
Turn the ignition to run (push START/STOP button once).
Press the (square) button, located on the instrument panel just behind the steering wheel to the left, to display the SETTINGS mode.
In the setting mode screen press (circle) button to move to MAINTENANCE.
Set a desired interval by pushing (circle) button to highlight ENGINE OIL and pressing (square) button. The reset mode will open up and allow you to enter the desired distance.
Select RESET and select new time or distance.
Repeat step 3 for ENGINE OIL FILTER. Turn the ignition off and then start the engine to verify the indicator has been reset.
2004-2006
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the ODO/TRIP knob then the turn ignition off.
Hold down the ODO/TRIP knob while turning the ignition key to the run position (one position before starting engine).
Hold down the button for 5 seconds or more. The odometer indicates “000000” and the light goes off.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2007-2009
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the trip meter reset knob then the turn ignition off.
Hold down the trip meter reset knob while turning the ignition key to the run position (one position before starting engine).
Hold down the button for 5 seconds or more. The odometer indicates “000000” and the light goes off.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2010
Turn the ignition to run (push START/STOP button once). Use the trip meter switch to bring up the trip meter A reading. Turn the ignition off.
While pressing the ěODO/TRIPî button, set the engine switch to run (push START/STOP button once).
Continue holding the “ODO/TRIP button for about 5 seconds. The resetting procedure is complete when “000000” in the trip metre flashes once and the message in the multi information display disappears.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2004-2006
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the trip meter reset knob then the turn ignition off.
Hold down the trip meter reset knob while turning the ignition key to the run position (one position before starting engine).
Hold down the knob until the light goes off. Before the light goes off, it illuminates 3 seconds, flashes for 2 seconds and illuminates for 1 second. If the system fails to reset, the light will remain flashing. In this case, return to step 1 and try again.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2007-2009
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the trip meter reset knob then the turn ignition off.
Hold down the trip meter reset knob while turning the ignition key to the run position (one position before starting engine).
Keep pressing the knob until the ěMAINT REQDî light goes off. If the light continues flashing, return to step 1 and try again.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2010
Turn the ignition to run – engine off (push START/STOP button once).
Press the Menu switch to change the multi-information display to blank. Turn the engine off.
While pressing the ODO/TRIP button, set the ěENGINE START STOP” switch to run – engine off (push START/STOP button once).
Keep pushing the ěODO/TRIPî switch for more than 7 seconds. While doing this operation, the master warning light comes on, a warning tone sounds and the “RESETTING OIL MAINTENANCE DATA” message appears to inform you that light has been reset. After 5 seconds, the system reset is completed.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2006
Turn the ignition to run (one position before starting engine).
Push the ěODO TRIPî switch to change the display to blank. Turn the ignition off.
While pressing the trip meter reset button, set the engine switch to run (one position before starting engine).
Keep pushing the ěRESETî switch for more than 7 seconds. While doing this operation, the master warning light comes on, a warning tone sounds and the “OIL MAINT RESET” message appears to inform you that light has been reset.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2007
Turn the ignition to run (one position before starting engine).
Press the ěDISPî switch to change the multi-information display to blank. Turn the ignition off.
While pressing the trip meter reset button, set the engine switch to run (one position before starting engine).
Keep pushing the ěRESETî switch for more than 7 seconds. While doing this operation, the master warning light comes on, a warning tone sounds and the “OIL MILEAGE RESET” message appears to inform you that light has been reset. After 5 seconds, the system reset is completed.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2008-2010
Turn the ignition to run – engine off (push START/STOP button once).
Press the ěDISPî switch to change the multi-information display to blank. Turn the ignition off.
While pressing the trip meter reset button, set the engine switch to run – engine off (push START/STOP button once).
Keep pushing the ěRESETî switch for more than 7 seconds. While doing this operation, the master warning light comes on, a warning tone sounds and the “OIL MESSAGE RESET” message appears to inform you that light has been reset. After 5 seconds, the system reset is completed.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2006-2010
Turn the ignition to run (one position before starting engine).
Press and release the stem in the lower center of the instrument cluster until the OIL LIFE message is displayed.
Once the alternating OIL LIFE and RESET messages appear, press and hold the stem until several beeps sound. This confirms that the oil life system has been reset.
Turn the ignition off and then start the engine to verify the indicator has been reset.
Designed by reset-service.com.