Skoda 2000
Longlife service intervals require diagnostic tool. Fixed intervals: Press and hold button below the speedometer. Turn ignition to the “ON” position.
“SERVICE” is displayed. Release button. Turn button below the tachometer to the right until display is reset. Turn ignition off.
Many Jeep vehicles track the intervals between oil changes to alert the driver when the next oil change is needed. A light illuminates on the control panel when the internal system determines it is time for an oil change. Most Jeep mechanics reset the oil light as part of the oil change service. If you change the oil in your Jeep yourself, you can manually reset the oil light. Resetting the oil light after an oil change allows the system to accurately track the time until the next oil change is needed. The procedures described in this article apply to 2010 Jeep models.
Instructions
1.Turn the ignition switch to the “ON” position. Do not start the engine.
2.Press the accelerator pedal completely to the floor slowly three times within a 10-second span.
3.Turn the ignition switch to the “OFF” position.
4.Turn the ignition switch to the “ON” position again. The oil light should be off. If the oil light is still illuminated, repeat the previous steps.
1985-1995
Turn the ignition to run (one position before starting engine).
Press and release the SERVICE REMINDER button until the desired item is displayed.
When the desired item is displayed, do not release SERVICE REMINDER button.
After button has been pressed for approximately 10 seconds, the service interval mileage display will begin to count down in 500 mile/km intervals.
When desired service interval mileage is reached, release button.
Turn the ignition off and then start the engine to verify the indicator has been reset.
1996-1997
Turn the ignition to run (one position before starting engine).
Display the oil life index on the Driver Information Centre.
Hold the RESET button for 5 seconds. When a DIC message of RESET is displayed and the oil life index equals 100%, the reset is complete.
Turn the ignition off and then start the engine to verify the indicator has been reset.
1998
Turn the ignition to run (one position before starting engine).
Press the TRIP button on the Driver Information Centre switch to view various menu choices, stop on OIL LIFE REMAINING.
Press and hold the RESET button on the DIC switch for more than 5 seconds. The oil life will change to 100%. The engine oil life monitor is now reset.
Turn the ignition off and then start the engine to verify the indicator has been reset.
1999
Turn the ignition to run (one position before starting engine).
Press and hold the OIL RESET button in the glove box for at least 5 seconds, but no more than 60 seconds.
After 5 seconds, observe the CHANGE OIL SOON light flash 4 times before light the turns off. This indicates that the engine oil life monitor system has reset.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2000-2005
Turn the ignition to run (one position before starting engine).
Display the oil life index on the Driver Information Centre.
Press and hold the RESET button for more than 5 seconds. The oil life will change to 100%.
Turn the ignition off and then start the engine to verify the indicator has been reset.
1985-1991
Turn the ignition to run (one position before starting engine).
Press and release the SERVICE REMINDER button until the desired item is displayed.
When the desired item is displayed, do not release SERVICE REMINDER button.
After button has been pressed for approximately 10 seconds, the service interval mileage display will begin to count down in 500 mile/km intervals.
When desired service interval mileage is reached, release button.
Turn the ignition off and then start the engine to verify the indicator has been reset.
Vehicles on fixed interval servicing can be reset as follows
Press and hold button “A” (positioned right of trip recorder display)
Switch ignition ON
The word “SERVICE” will appear in the trip recorder display
Release button “A”
Turn button “B” (positioned left of trip recorder display) to the right to reset the display
Switch ignition OFF
This applies to fixed service intervals only appearently
Button “A” is the trip reset
Button “B” is the clock set