2009-2011
1. Push the ignition switch to the ON position (do not start the engine). Use the ENTER button (?) and toggle the vehicle information display to show the SETTING screen. Use the NEXT button (?) to select.
2. Use the NEXT button (?) to select MAINTENANCE
i) SETTING > MAINTENANCE > OIL > ENGINE OIL to set or reset the mileage for the engine oil change.
ii) SETTING > MAINTENANCE > FILTER > to set or reset the mileage for the engine oil filter.
3. Turn the ignition off and then start the engine to verify the indicator has been reset.
How can you reset service light, maintance on Toyota Avensis
1. Set the multi-information display to TRIP A.
2. Turn the ignition switch off.
3. Press and hold the ODO / TRIP switch, and turn the ignition switch on (IG).
4. After turning the ignition switch on (IG), keep holding the switch for at least 5 seconds.
1986-1988
Turn the ignition to run (one position before starting engine).
The oil life index may be reset by pressing and holding the ENGINE DATA and GAGE buttons until Oil Index 100 message appears in the information display panel.
Turn the ignition off and then start the engine to verify the indicator has been reset.
1989
Turn the ignition to run (one position before starting engine).
Press ENG DATA until oil life index is displayed.
Press ENG DATA and GAGE simultaneously until oil life index resets to 100.
Turn the ignition off and then start the engine to verify the indicator has been reset.
1990
Turn the ignition to run (one position before starting engine).
Press ENG DATA until oil life index is displayed.
Press RESET/ENTER until oil life index resets to 100.
Turn the ignition off and then start the engine to verify the indicator has been reset.
1991-1992
Without Visual Information Centre:
Turn the ignition to run (one position before starting engine).
Press OPTIONS until oil life index is displayed.
Press RESET/ENTER until oil life index resets to 100 (hold about 5 seconds).
Turn the ignition off and then start the engine to verify the indicator has been reset.
With Visual Information Centre:
Turn the ignition to run (one position before starting engine).
Press INFO key then OIL LIFE key to display oil life index.
Press RESET key until oil life index resets to 100.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2005-2009
Manual Reset Procedure:
Press and hold the trip reset button.
Turn the ignition switch on to the ignition position II (one position before starting engine).
If the SII (Service Indicator Interval) function is enabled the information display will flash ‘SERVICE’ for 5 seconds and then display ‘SERVICE’ constantly. If the SII function is not enabled the information display will show the normal odometer and trip information.
If the trip reset button is released within 10 seconds of entering the reset mode, the information display will show ‘DIST’. If the trip reset button is not released after 10 seconds the instrument cluster will exit the manual reset procedure.
If the oil service value is to be reset, press the trip reset button within 10 seconds for 5 seconds and then reset the oil service value, the display will then show ‘END’.
If the trip reset button is pressed for 5 seconds the display will exit the reset routine. If the trip reset button is not pressed for more than 10 seconds, then the information display will exit the reset routine. Turn the ignition off and then start the engine to verify the indicator has been reset.
005-2008
Turn the ignition to run (one position before starting engine).
Ensure odometer reading is shown. Turn ignition off.
While holding down the trip meter reset knob turn the ignition to run (one position before starting engine).
Hold down knob for at least 5 seconds. The odometer indicates “000000” and the light goes off. If the system fails to reset, the light will continue flashing.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2009-2010
1.Turn the ignition to run (one position before starting engine).
2.Ensure Trip Metre A reading is shown. Turn the ignition off.
3.While holding down the trip meter reset knob turn the ignition to run (one position before starting engine).
Without multi-information display
4. Continue to press and hold the button until the trip meter displays “000000”.
With multi-information display
4. Continue to press and hold the button until ěMAINT REQD RESET MODE COMPLETE” appears on the multi-information display.
5. Turn the ignition off and then start the engine to verify the indicator has been reset.