Find how to reset any maintenance light or reset oil life after an oil change for all makes and models.

Data

Oil service reset Tornado

1986-1988

Turn the ignition to run (one position before starting engine).
The oil life index may be reset by pressing and holding the ENGINE DATA and GAGE buttons until Oil Index 100 message appears in the information display panel.
Turn the ignition off and then start the engine to verify the indicator has been reset.

1989

Turn the ignition to run (one position before starting engine).
Press ENG DATA until oil life index is displayed.
Press ENG DATA and GAGE simultaneously until oil life index resets to 100.
Turn the ignition off and then start the engine to verify the indicator has been reset.

1990

Turn the ignition to run (one position before starting engine).
Press ENG DATA until oil life index is displayed.
Press RESET/ENTER until oil life index resets to 100.
Turn the ignition off and then start the engine to verify the indicator has been reset.

1991-1992

Without Visual Information Centre:
Turn the ignition to run (one position before starting engine).
Press OPTIONS until oil life index is displayed.
Press RESET/ENTER until oil life index resets to 100 (hold about 5 seconds).
Turn the ignition off and then start the engine to verify the indicator has been reset.
With Visual Information Centre:
Turn the ignition to run (one position before starting engine).
Press INFO key then OIL LIFE key to display oil life index.
Press RESET key until oil life index resets to 100.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Service oil reset Lexus GX – Series

2004-2006
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the trip meter reset knob then the turn ignition off.
Hold down the trip meter reset knob while turning the ignition key to the run position (one position before starting engine).
Hold down the knob until the light goes off. Before the light goes off, it illuminates 3 seconds, flashes for 2 seconds and illuminates for 1 second. If the system fails to reset, the light will remain flashing. In this case, return to step 1 and try again.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2007-2009
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the trip meter reset knob then the turn ignition off.
Hold down the trip meter reset knob while turning the ignition key to the run position (one position before starting engine).
Keep pressing the knob until the ěMAINT REQDî light goes off. If the light continues flashing, return to step 1 and try again.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2010
Turn the ignition to run – engine off (push START/STOP button once).
Press the Menu switch to change the multi-information display to blank. Turn the engine off.
While pressing the ODO/TRIP button, set the ěENGINE START STOP” switch to run – engine off (push START/STOP button once).
Keep pushing the ěODO/TRIPî switch for more than 7 seconds. While doing this operation, the master warning light comes on, a warning tone sounds and the “RESETTING OIL MAINTENANCE DATA” message appears to inform you that light has been reset. After 5 seconds, the system reset is completed.
Turn the ignition off and then start the engine to verify the indicator has been reset.

service light reset SPRINTER

How to reset the Maintenance Service interval:

Metod 1

– Switch ignition on to position one, (first click clockwise);
– “Outside temperature” should be displayed, if not move to it (You have to be in this display to go further);
– Press the trip odometer, “reset”, knob three times consecutively ( The Voltage display will appear);
– Press Down Arrow to enter the “Service Menu”. “Service Data” submenu below will be highlighted.
– Press right page to enter the Service data submenu. (Left page goes up in menus, -+ selects items displayed)
– Press – three times on right of wheel to highlight “Confirmation”.
– Use right page to select to display sub-menu as to what to confirm.
– Select “Full Service” (No need to use -+.) to confirm this choice
– Press right page to confirm. (Delay is about 3 seconds.)
– Press left page twice to exit the menu system, or turn off the ignition switch.
– Turn off ignition. Turn back on. The display should show that it is recalculating the mileage and days. This takes about 60 seconds so be patient.

Metod 2

1. Put the key in the ignition and switch it on without starting the engine.
(Wait for LCD to return to the vehicle mileage)
2. Hold the “O” button down till you hear a beep (could take a while, 30 sec.)
3. Press the M button repeatedly and a number of reset menus will appear, (If you have used oil according to quality sheet 229.31 or 228/229.51 you can scroll to Reset.31 or Reset.51 respectively.) Select “reset 51”
4. Now, when appropriate oil type is selected press “O” for 6 seconds until ”2” is displayed.
5. Press “O” once again briefly and the ” reset done” message will confirm that the job is done.
6. Pull the Key out

FOR THE 2004 DODGE SPRINTER!

Turn the key to position 2 in the ignition lock and immediately press the button MI (km) twice.
Within 10 seconds, return the key to the 0 in the ignition lock.
Press and hold the button MI (km). Turn the key to position 2 in the ignition lock. Keep the button MI (km) pressed.
The maintenance indicator with the time/distance is shown.
After about 10 seconds, an acoustic signal will sound and the maintenance indicator is displayed with the new remaining time / distance .
Release the button MI (km)

Categories





Copyright © 2013. All Rights Reserved.