Reset service light indicator Renault Scenic 2. From year: 2003, 2004, 2005, 2006, 2007, 2008, 2009.
How to reset service light indicator Renault Scenic 2.
1. Turn the ignition to ON position 2, don’t start the vehicle.
2. On cars with keycard ignition, insert the card, then push & hold the start button for 5 seconds to turn on the dashboard cluster lights.
3. Push & button on the end of the wiper stalk repeatedly until the warning spanner symbol and miles to service appears on the monitor, some models have 2 buttons, which cycle through the options in opposite directions, either button can be used in this case.
4. Push & hold the button.
5. The display will now change to the new service interval and start flashing.
6. Keep holding the button until the display stops flashing.
7. Release the button, turn ignition to off and start the car to see if warning light has been reset.
Reset service light indicator Renault Megane 2. From year: 2002, 2003, 2004, 2005, 2006, 2007, 2008.
How to reset service light indicator Renault Megane 2.
To reset Service Due Now on a Renault Megane 2, follow these steps:
1. Switch ON the gnition, don’t start the vehicle. For cars with keycard ignition, insert the card, then push & hold the start button for 5 seconds to turn on the dashboard cluster.
2. Push and release the button on the end of the wiper stalk until the Service Due Now message appears on the display. Some models have 2 buttons, which cycle through the options in opposite directions, either button can be used in this case.
3. When Service Due Now message is displayed push and hold the same button located at the end of wiper stalk.
4. Now the Service Due now will start to flash after that the display will change to the new service interval and still flashing.
5. Keep holding the button until the display stops flashing.
6. Done, have managed to reset service light indicator Renault Megane 2.
Instructions
1. Open the hood and loosen the retaining nut on the cable clamp running to the negative battery terminal.
2. Slide the clamp off of the negative battery terminal.
3. Wait 1 minute for the Range Rover’s electronic control module to cycle and reset. Then, reconnect the clamp to the negative battery terminal.
4. Tighten the retaining nut on the cable clamp. The airbag light should go out at this point. When it does, you’ll know that the fault code has been erased.
The service light on these vehicles is usually a spanner / wrench symbol. To reset that indicator:
Turn the Ignition ON (position 2) but do not start the engine
(On cars with keycard ignition, insert the card, then press and hold the start button for 5 seconds to turn on the dash cluster)
Press the button on the end of the wiper stalk repeatedly until the spanner symbol and miles to service appears on the display
(Some models have 2 buttons, which cycle through the options in opposite directions – either button can be used in this case)
Press and hold the button
The display will now change to the new service interval and start flashing
Keep holding the button until the display stops flashing
Release the button
The directions that come with your vehicle are lousy, and the process stinks to. And keep in mind that if you do not press the buttons fast enough, or hold long enough, you must start over. It usually takes a few tries. Here’s how to do it:
1.) Press the TRIP/RESET button to cycle to “SETUP MENU HOLD RESET”.
2.) Now press and hold the button for 2 seconds until “RESET FOR SYSTEM CHECK” is displayed, then release.
3.) Imediately press and hold button for 2 more seconds until “Oil 100% RESET IF NEW” is displayed, then release.
4.) Imediately press button once to display “HOLD RESET IF NEW OIL” and release.
5.) Imediately press and hold button for 2 seconds until “OIL LIFE SET TO 100%” is displayed.
If you have done this dance properly, without delaying too long between steps, you are done. What a pain in the butt just to reset the oil maintenance light!!!