Find how to reset any maintenance light or reset oil life after an oil change for all makes and models.

counter

RESET SERVICE LIGHT SKODA OCTAVIA 2

Reset service light Skoda Octavia 2, 2004, 2005, 2006, 2007

1. Switch off the ignition and press the reset knob of the trip counter below the speedometer and hold.

2. Switch on the ignition and release the reset button, one of the service events appear in the display.

3. It is possible to switch between the the readouts of the service events by briefly pressing the reset button.

4. When the particular service event is displayed, turn the button for setting the digital clock to the right, service appears in the display.

5. Switch off the ignition. Only now is the service event reset.

SERVICE INDICATOR SYSTEM SEAT CORDOBA

Service indicator system Seat Cordoba, 1993, 1994, 1995, 1996, 1997, 1998, 1999

IN00, No service is required, standard display.

OEL, When 7500 miles has been reached before the yearly service is required.

IN01, Indicates time for the yearly service inc oil change.

IN02, Indicates it is time for the Major service. T

O RESET THE INDIVIDUAL COUNTERS.

1) turn on ignition (do not start).

2) Press the trip reset button button on the speedo (the trip value will not reset to zero but will reappear when the procedure is finished).

3) Turn off the ignition and thne release the trip reset button. In the LCD display you will see the word OEL. Using the minute set button for the clock (lower one) you will reset the OEL interval counter. Press it, hold, release, 5 horizontal lines will appear in the display.

4) press and release the trip reset button. In the LCD display you will see IN01 repeat step 3 to reset the inspection counter when required.

5) Again press the trip reset and rest the IN02 counter if necessary. If doing an oil change only reset the OEL counter. If doing an inspection service reset both the OEL and IN01 counters. If doing a full service reset all 3, OEL, IN01 and ,IN02.

6) Turn on ignition (do not start the car).

7) After the appearance of the IN00 display turn off the ignition.

8) You are done the trip counter should read as it did before you started.

PROGRAMMING THE INTERVALS TO REQUIREMENTS

With todays higher spec oils and/or peoples need and desire to service more regular there is a way to alter the counters to your prefered settings (within reason).

1) Turn on ignition (dont start the car).

2) press the trip reset button also press the Minute set button on the clock (lower one).

3) The LCD display OEL 1,S where the S indicates SET.

4) Using the trip reset button you can call up the following counter data in sequence.

OEL 1,S Distance counter for oil change (7500 standard).

OEL 2,S Time counter for oil change (12 months).

IN 01,S Time counter for yearly service interval (12 months).

IN 02,S Distance counter for full service (15000 miles).

5) Using the minute SET button on the clock (lower one) you can display the current value repeated pressing of the button will select a subsequent lower value and at the lowest level will reset to the highest and start to decrease again (so dont panic). the steps work in miles (500 at a time) and time steps in bi-monthly (1, 2months) i.e.1,2,3,4,5,6.

6) Once you have set the counter to the value you require turn off the ignition.

7) Job done

Reset the service indicator light 2007 Renault clio

Turn on the ignition, but don’t start the car. On the right stalk there is a toggle switch that hinges up and down, and is used for going through the different features of the display. When the display shows ‘Service Due’ press and hold the top part of this switch for 10 seconds until the dispaly resets and it shows 30,000km or whatever until next service.
Turn on the ignition, but don’t start the car. On the right stalk there is a toggle switch that hinges up and down, and is used for going through the different features of the display. When the display shows ‘Service Due’ press and hold the top part of this switch for 10 seconds until the dispaly resets and it shows 30,000km or whatever until next service.

all of the above is correct apart from pressing the toggle button. if you instead press the bottom toggle button for 10 seconds the display will start to flash. Keep button depressed and 5 seconds later the service counter will reset.

Reset Service Message Volvo S80

S80

Turn ignition switch to position I
Press and hold “day counter reset button”
Turn ignition to position II
Continue holding day counter for about 10 seconds
While SRL flashes, release day counter button
Should hear “beep-beep” to confirm command accepted

ibiza/cordoba 93-99 service indicator system

SERVICE INTERVAL DISPLAY

the computer has counters that not only count the miles from the speedo but also
a time count as well

Displays:

IN00 – No service is required – standard display

OEL – When 7500 miles has been reached before the yearly service is required

IN01 – Indicates time for the yearly service inc oil change

IN02 – Indicates it is time for the Major service

TO RESET THE INDIVIDUAL COUNTERS

1- turn on ignition (do not start)

2- Press the trip-reset button button on the speedo (the trip value will not reset to
zero but will reappear when the procedure is finished)

3- Turn off the ignition and thne release the trip-reset button

In the LCD display you will see the word “OEL”

Using the minute set button for the clock (lower one) you will reset the OEL interval
counter

press it – hold – release – 5 horizontal lines will appear in the display

4- press and release the trip-reset button

In the LCD display you will see “IN01” repeat step 3 to reset the inspection counter when required

5- Again press the trip-reset and rest the “IN02” counter if necessary

If doing an oil change only reset the “OEL” counter

If doing an inspection service reset both the “OEL” and “IN01” counters

If doing a full service reset all 3 – “OEL” “IN01” & “IN02”

6- Turn on ignition (do not start the car)

7- After the appearance of the “IN00” display turn off the ignition

8- You are done – the trip counter should read as it did before you started

PROGRAMMING THE INTERVALS TO REQUIREMENTS

With todays higher spec oils and/or peoples need and desire to service more regular there is a way
to alter the counters to your prefered settings (within reason)

1- Turn on ignition (don’t start the car)

2- press the trip-reset button also press the Minute set button on the clock (lower one)

3- The LCD display “OEL 1,S” where the “S” indicates SET

4- Using the trip-reset button you can call up the following counter data in sequence

OEL 1,S – Distance counter for oil change (7500 standard)

OEL 2,S – Time counter for oil change (12 months)

IN 01,S – Time counter for yearly service interval (12 months)

IN 02,S – Distance counter for full service (15000 miles)

5- Using the minute SET button on the clock (lower one) you can display the current value
repeated pressing of the button will select a subsequent lower value and at the lowest level
will reset to the highest and start to decrease again (so don’t panic)

the steps work in miles (500 at a time) and time steps in bi-monthly (1=2months) i.e.1-2-3-4-5-6

6- Once you have set the counter to the value you require – turn off the ignition

7- Job done

Categories





Copyright © 2013. All Rights Reserved.