1999-2003
Turn the ignition to run (one position before starting engine).
Push the RESET button located in the drivers instrument panel fuse block. The CHANGE OIL light will start to flash.
Press and hold the RESET button again. The reset is complete when you hear the chimes and the CHANGE OIL light goes out.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2004
Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds. The reset is complete when the chimes sound and the CHANGE OIL lamp goes out. If the lamp stays on and and no chime is heard, repeat the reset procedure.
Turn the ignition off and then start the engine to verify the indicator has been reset.
Engine Oil Change Indicator System
Oil Change Required
Your vehicle is equipped with an engine oil change
indicator system. The “Oil Change Required” message
will flash in the EVIC display for approximately 10
seconds after a single chime has sounded to indicate the
next scheduled oil change interval. The engine oil change
indicator system is duty cycle based, which means the
engine oil change interval may fluctuate dependent upon
your personal driving style.
Unless reset, this message will continue to display each
time you turn the ignition switch to the ON/RUN
position. To turn off the message temporarily, press and
release the MENU button. To reset the oil change indicator
system (after performing the scheduled maintenance)
refer to the following procedure.
1. Turn the ignition switch to the ON position (Do not
start the engine).
2. Fully depress the accelerator pedal slowly three times
within 10 seconds.
3. Turn the ignition switch to the OFF/LOCK position.
NOTE: If the indicator message illuminates when you
start the vehicle, the oil change indicator system did not
reset. If necessary repeat this procedure.
2004-2007
Turn the ignition to run (one position before starting engine).
Press and release the trip/reset button until the OIL LIFE message is displayed.
Then press and hold the trip/reset button until a chime sounds 5 times, and RESET is displayed in the message centre. When the system is reset, the odometer will again be displayed in the message centre.
Turn the ignition off and then start the engine to verify the indicator has been reset.
1999-2003
Turn the ignition to run (one position before starting engine).
Press the RESET button (in fuse panel block inside driver side door)and release. The CHANGE OIL indicator will start flashing.
Press and hold the RESET button until audible chime is heard and then release.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2004-2005
Turn the ignition to run (one position before starting engine).
Immediately after Step 1 press and release the gas pedal 3 times within 5 seconds. The reset is complete when you hear the chimes and the CHANGE OIL light goes out.
Turn the ignition off and then start the engine to verify the indicator has been reset.
1994-2002
Turn the ignition to run (one position before starting engine).
This message can be deleted by first briefly pressing the CLR button, then depressing it a second time for at least 8 seconds until “SERVICE” appears on the display and a chime sounds.
Turn the ignition off and then start the engine to verify the indicator has been reset.
*The message can only be deleted when it is shown on the SID (Service Indicator Display).
2003-2006
Turn the ignition to run (one position before starting engine).
Press the CUSTOMIZE button.
Select System Settings using the INFO dial. Press the INFO dial.
Select Service Info. Press in the INFO dial.
Select Reset Service Ind. Press in the INFO dial.
When asked Are you sure? Select Yes. Turn the ignition off and then start the engine to verify the indicator has been reset.
2007-2009
Turn the ignition to run (one position before starting engine).
Select Settings using the steering wheel controls (up or down arrow).
Press and hold the SET button until given audible confirmation.
Select Time for Service.
Press the SET button.
To the question Reset Service Ind? Select YES. Turn the ignition off and then start the engine to verify the indicator has been reset.