Center

Oil service reset GL – Class

2007-2012

1. Turn the ignition to position 1. (close all doors
2. Press the system selection button (3 located on the lower left of the steering wheel) repeatedly until the kilometer or temperature reading is shown in the multi information display.)
3. Press the TRIP reset button (center button on instrument panel) quickly 3 times. An audible beep will be heard followed by the battery voltage displayed.
4. Press the scoll forward/back button (left side of steering wheel) to highlight the “”Service menu””.”
5. Use the +/- buttons to select “”Confirmation”” menu. Press the system select button to confirm. The menu item “”Complete service”” is highlighted.”
6. Press the system selection button to confirm. “”Service confirmed”” appears.”
7. Use the scroll forward/back button to exit the menu.
8. Turn the ignition off and then start the engine to verify the indicator has been reset.

Oil service reset R – Class

2006-2012

Oil service reset SLK – Class

1998-1999
*Diagnostic Reset Tool Required
Manual Reset:

1. Turn key in steering lock to position 2.
2. Within 4 seconds press button (1) left of speedometer twice.
3. The present status for days or distance displays
4. Press and hold button (1)
5. Continue to hold button (1) for approximately 10 seconds until a signal sounds and the display shows 10 000 mils or 15 000km. Release button (1).
6. Turn the ignition off and then start the engine to verify the indicator has been reset.
2000-2001
*Diagnostic Reset Tool Required

Manual Reset:

1. Switch ignition on and immediately press knob to left of speedometer twice within 4 seconds.
2. Present status for days or distance is now displayed. Within 10 seconds
3. Press and hold button to the left of speedometer
4. Release button.
5. Service interval displays the reset interval.
6. Turn the ignition off and then start the engine to verify the indicator has been reset.

2002-2004
1. Switch ignition on and immediately press knob to left of speedometer twice within 1 second.
2. Present status for days or distance is now displayed. Within 10 seconds
3. Press and hold button to the left of speedometer
4. Release button.
5. Service interval displays the reset interval.
6. Turn the ignition off and then start the engine to verify the indicator has been reset.

2005-2009
1. Turn the ignition to position 1.
2. Press the system selection button (3 located on the lower left of the steering wheel) repeatedly until the kilometer reading is shown in the multi information display.)
3. Press the cluster illumination button (lower left of instrument panel) quickly 3 times. The battery voltage will be displayed.
4. Press the up or down buttons until the service menu appears.
5. Use the +/- buttons to select menu oprion “”CONFIRM””.”
6. Press the system selection button uuntil “”COMPLETE SERVICE”” is selected.”
7. Confirm “”Complete Service”” with system selection button. The display will show “”SERVICE CONFIRMED””.”
8. Turn the ignition off and then start the engine to verify the indicator has been reset.

2010-2012
1. Turn the ignition to position 1. (close all doors
2. Press the scroll forward button (bottom button on left side of steering wheel controls) to display mileage counter.
3. Press the system selection button (left button on left side of steering wheel controls) repeatedly until the menu item “”trip”” with highlighter is displayed. “”Trip”” remains selected for 5 seconds so move quickly to step 4.”
4. Press and hold accept/end phone button and within 1 second press and hold the button in the center of the arrows (left side of steering wheel). In 5 seconds the Workshop menu will be displayed “”Vehicle data
5. Use scroll forward or backward to highlight “”ASSYST PLUS”” and confirm selection using the button in the center of the arrows. “”Service data”” and “”Full service”” appear in the display.”
6. Use scroll forward or backward to select “”Full service”” and confirm selection with the button in the center of the arrows. The display will show “”Service 1
7. Use scroll forward or backward to select “”Confirm serv”” and confirm selection with the button in the center of the arrows.”
8. Use scroll forward or backward to select engine oil specification used. “”Oil qual. 229.3″” and “”Oil qual. 229.5″” are displayed. Confirm selection with center button. The display shows “”Serv conducted?”””
9. Use scroll forward or backward to select “”Yes”” and confirm with center button. Display will show “”Take-back not possible
10. Use scroll forward or backward until “”Configuration”” is highlighted and confirm selection with button in center of the arrows. “”Full service carried out”” appears in the display.”
11. Use scroll forward and backward to exit menu.
12. Turn the ignition off and then start the engine to verify the indicator has been reset.

Reset oil service light Jaguar XF

Reset oil service light Jaguar XF. How to reset maintenance light, reset service light indicator. Can be made manually by use button on car dash board.

How do you reset oil service light Jaguar XF.

Press and hold rear fog lamp switch Ignition on, do not start engine.
Release rear fog lamp switch.
Press and hold trip button (end of left side stalk).
Press and hold rear fog lamp switch See resetting service light message in message center.
The rear fog light switch is just below the trunk release on the lower left side of the steering wheel.
The message center is between the speedo and tach ,bar, not the touch screen.

Reset oil service light Ford Explorer Sport Trac

Reset oil service light Ford Explorer Sport Trac. From years: 1999, 2000, 2001, 2002, 2003, 2004, 2005, 2006, 2007, 2008, 2009, 2010.

How do you reset oil service light Ford Explorer Sport Trac. From years:1999, 2000, 2001.

Turn the ignition to run, one position before starting engine.
Press and hold the OIL CHANGE RESET control for 5 seconds. The message centre will count down for 5 seconds and the message centre will display OIL LIFE RESET TO 100%.
Turn the ignition off and then start the engine to verify the indicator has been reset.

How to reset oil service light Ford Explorer Sport Trac. From years: 2002, 2003.

Turn the ignition to run , ne position before starting engine.
Press the SETUP control to access the System Check function.
Press and release the RESET control to display OIL LIFE XX% HOLD RESET NEW.
Press and hold the RESET control for 2 seconds to display IF NEW OIL HOLD RESET.
Press and hold the RESET control to display OIL LIFE SET TO 100%. Your oil life is now reset.
Turn the ignition off and then start the engine to verify the indicator has been reset.

Full procedure how to reset oil service light Ford Explorer Sport Trac. From years: 2004, 2005.

Turn the ignition to run, one position before starting engine.
Select this function from the SETUP control PRESS RESET AT OIL CHANGE.
Press RESET control to reset oil change.
Turn the ignition off and then start the engine to verify the indicator has been reset.

How can you reset oil service light Ford Explorer Sport Trac. From years: 2006, 2007.

To reset the oil monitoring system to 100% after each oil change Ford Explorer Sport Trac. From years: 2006, 2007 [approximately 5,000 miles (8,000 km) or 180 days] perform the following.

Turn the ignition to run, one position before starting engine.
Enter SYSTEM CHECK to display “OIL XXX% OIL LIFE OK”.
Press RESET control to display “HOLD RESET IF NEW OIL”.
Press and hold the RESET control for more than 2 seconds. Oil life is set to 100% and “OIL CHANGE SET TO 100%” is displayed.

Note: To change oil life 100% miles value from 5,000 miles (8,000 km) or 180 days to another value, refer to the Oil Life Start Value selected from the SETUP MENU in this section.

Reset Oil life Start Value Ford Explorer Sport Trac. From years: 2006, 2007.

Select this function from the SETUP control for the current display mode.
Each press of the RESET control reduces the value by 10 percent.

Note: Oil Life Start Value of 100% equals 5,000 miles (8,000 km) or 180 days. For example, setting Oil Life Start Value to 60% sets the Oil Life Start Value to 3,000 miles (4,828 km) and 120 days.

How do you reset oil service light Ford Explorer Sport Trac. From years:2008, 2009, 2010.

To reset the oil monitoring system to 100% after each oil change Ford Explorer Sport Trac. From years: 2008, 2009, 2010 [approximately 7,500 miles (12,070 km) or 6 months] perform the following.

Turn the ignition to run, one position before starting engine.
Press RESET control to display “HOLD RESET IF NEW OIL”.
Press and hold the RESET control for more than 2 seconds. Oil life is set to 100% and “OIL CHANGE SET TO 100%” is displayed.
Note: To change oil life 100% miles value from 7,500 miles (12,070 km) or 6 months to another value, proceed to step 5.
Once “OIL LIFE SET TO XXX%” is displayed, release and press the RESET control switch to change the Oil Life Start Value. Each release and press will reduce the value by 10 percent.
Note: Oil Life Start Value of 100% equals 7,500 miles (12,070 km) or 6 months. For example, setting Oil Life Start Value to 60% sets the Oil Life Start Value to 3,000 miles (4,828 km) and 120 days.

OIL CHANGE REQUIRED. Displayed when the engine oil life remaining is 0%.

An oil change is required whenever indicated by the message center and according to the recommended maintenance schedule.

ENGINE OIL CHANGE SOON. Displayed when the engine oil life reaches 5% or less of the Oil Life Start Value.