Reset service light indicator Renault Megane 2. From year: 2002, 2003, 2004, 2005, 2006, 2007, 2008.
How to reset service light indicator Renault Megane 2.
To reset Service Due Now on a Renault Megane 2, follow these steps:
1. Switch ON the gnition, don’t start the vehicle. For cars with keycard ignition, insert the card, then push & hold the start button for 5 seconds to turn on the dashboard cluster.
2. Push and release the button on the end of the wiper stalk until the Service Due Now message appears on the display. Some models have 2 buttons, which cycle through the options in opposite directions, either button can be used in this case.
3. When Service Due Now message is displayed push and hold the same button located at the end of wiper stalk.
4. Now the Service Due now will start to flash after that the display will change to the new service interval and still flashing.
5. Keep holding the button until the display stops flashing.
6. Done, have managed to reset service light indicator Renault Megane 2.
Switch Ign on (do not start engine)
Set Odometer to read total miles.
Press Odometer Button (OB) until CFG1 appears in display
Release the OB.
Pressing the OB briefly will change between CFG1, CFG2, CFG3, CFG1
Once you have selected the CFG (see below).
Press the OB again for 5secs to store the new service frequency.
Turn off the ignition.
I selected CFG1 for my vehicle (05 Reg 2.8JTD), but you must decide yourself for your vehicle, should take 5mins to read this and carry out the resetting procedure
Note: If your vehicle is under warranty and you take it to be serviced by a Fiat dealer they will do this as part of the service.
CFG1 = 30000km (18,600mi) and 365 days in cases of Standard Use for 2.0 petrol and 2.8JTD versions, or in the case of Severe Use for the 2.3JTD versions.
CFG2 = 20000km (12,500mi) and 365 days in case of Standard Use for 2.0JTD versions, or in case of severe use for 2.0 petrol and 2.8JTD versions
CFG3 = 15000km (9,300mi) and 365 days in case of Severe Use for 2.0JTD versions
2005-2009
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the trip meter reset knob then the turn ignition off.
Hold down knob while turning the ignition key to the run position (one position before starting engine).
Hold down the knob until the light goes off. Before the light goes off, it illuminates for 3 seconds, flashes for 2 seconds and illuminates for 1 second. If the system fails to reset, the light will remain flashing. In this case, return to step 1 and try again.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2010
Start the engine and bring up the trip meter A reading.
Vehicles with smart key system:
Turn the “ENGINE START STOP” switch off.
While pressing the Trip Meter reset button, press the “ENGINE START STOP” switch once (do not start engine).
Continue to press and hold the button until the trip meter displays “000000”.
1.Turn the ignition off and then start the engine to verify the indicator has been reset.
Vehicles without smart key system:
2. Turn the ignition switch off.
3. While holding down the trip meter reset knob turn the ignition to run (one position before starting engine).
4. Hold down knob for at least 5 seconds. The odometer indicates “000000” and the light goes off. If the system fails to reset, the light will continue flashing.
5. Turn the ignition off and then start the engine to verify the indicator has been reset.
2005-2006
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the ODO/TRIP knob then the turn ignition off.
Hold down ODO/TRIP knob while turning the ignition key to the run position (one position before starting engine).
Hold down the knob until the light goes off. Before the light goes off, it illuminates
3 seconds, flashes for 2 seconds and illuminates for 1 second. If the system fails to reset, the light will remain flashing. In this case, return to step 1 and try again.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2007
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the ODO/TRIP knob then the turn ignition off.
Hold down ODO/TRIP knob while turning the ignition key to the run position (one position before starting engine) for longer than 7 seconds. While doing this operation, the “engine oil replacement” reminder light goes off. If the system fails to reset, the light will remain flashing. In this case, return to step 1 and try again.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2008-2010
Turn the engine on by holding the START/STOP switch. Use the trip meter switch to bring up the trip meter A reading. Turn the ignition off.
While pressing the trip meter reset button, set the engine switch to run (push START/ STOP button once) and continue to press and hold the knob until the multi information display indicates that the reset is complete.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2004-2006
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the trip meter reset knob then the turn ignition off.
Hold down the trip meter reset knob while turning the ignition key to the run position (one position before starting engine).
Hold down the knob until the light goes off. Before the light goes off, it illuminates 3 seconds, flashes for 2 seconds and illuminates for 1 second. If the system fails to reset, the light will remain flashing. In this case, return to step 1 and try again.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2007-2009
Turn the ignition to run (one position before starting engine).
Bring up the odometer reading using the trip meter reset knob then the turn ignition off.
Hold down the trip meter reset knob while turning the ignition key to the run position (one position before starting engine).
Keep pressing the knob until the ěMAINT REQDî light goes off. If the light continues flashing, return to step 1 and try again.
Turn the ignition off and then start the engine to verify the indicator has been reset.
2010
Turn the ignition to run – engine off (push START/STOP button once).
Press the Menu switch to change the multi-information display to blank. Turn the engine off.
While pressing the ODO/TRIP button, set the ěENGINE START STOP” switch to run – engine off (push START/STOP button once).
Keep pushing the ěODO/TRIPî switch for more than 7 seconds. While doing this operation, the master warning light comes on, a warning tone sounds and the “RESETTING OIL MAINTENANCE DATA” message appears to inform you that light has been reset. After 5 seconds, the system reset is completed.
Turn the ignition off and then start the engine to verify the indicator has been reset.