2007-2012
1. Turn the ignition to position 1. (close all doors
2. Press the system selection button (3 located on the lower left of the steering wheel) repeatedly until the kilometer or temperature reading is shown in the multi information display.)
3. Press the TRIP reset button (center button on instrument panel) quickly 3 times. An audible beep will be heard followed by the battery voltage displayed.
4. Press the scoll forward/back button (left side of steering wheel) to highlight the “”Service menu””.”
5. Use the +/- buttons to select “”Confirmation”” menu. Press the system select button to confirm. The menu item “”Complete service”” is highlighted.”
6. Press the system selection button to confirm. “”Service confirmed”” appears.”
7. Use the scroll forward/back button to exit the menu.
8. Turn the ignition off and then start the engine to verify the indicator has been reset.
2006-2012
1. Turn the ignition to position 1. (close all doors
2. Press the system selection button (3 located on the lower left of the steering wheel) repeatedly until the kilometer or temperature reading is shown in the multi information display.)
3. Press the TRIP reset button (center button on instrument panel) quickly 3 times. An audible beep will be heard followed by the battery voltage displayed.
4. Press the scoll forward/back button (left side of steering wheel) to highlight the “”Service menu””.”
5. Use the +/- buttons to select “”Confirmation”” menu. Press the system select button to confirm. The menu item “”Complete service”” is highlighted.”
6. Press the system selection button to confirm. “”Service confirmed”” appears.”
7. Use the scroll forward/back button to exit the menu.
8. Turn the ignition off and then start the engine to verify the indicator has been reset.
Reset maintenance light on Dodge Sprinter
1. Put the key in the ignition and switch it on without starting the engine.
(Wait for LCD to return to the vehicle mileage)
2. Hold the “O” button down till you hear a beep (could take a while, 30 sec.)
3. Press the M button repeatedly and a number of reset menus will appear, (If you have used oil according to quality sheet 229.31 or 228/229.51 you can scroll to Reset.31 or Reset.51 respectively.) Select “reset 51″
4. Now, when appropriate oil type is selected press “O” for 6 seconds until ”2” is displayed.
5. Press “O” once again briefly and the ” reset done” message will confirm that the job is done.
6. Pull the Key out
FOR THE 2004 DODGE SPRINTER!
Turn the key to position 2 in the ignition lock and immediately press the button MI (km) twice.
Within 10 seconds, return the key to the 0 in the ignition lock.
Press and hold the button MI (km). Turn the key to position 2 in the ignition lock. Keep the button MI (km) pressed.
The maintenance indicator with the time/distance is shown.
After about 10 seconds, an acoustic signal will sound and the maintenance indicator is displayed with the new remaining time / distance .
Release the button MI (km)
S80
Turn ignition switch to position I
Press and hold “day counter reset button”
Turn ignition to position II
Continue holding day counter for about 10 seconds
While SRL flashes, release day counter button
Should hear “beep-beep” to confirm command accepted
1. Put the key in the ignition and switch it on without starting the engine.
(Wait for LCD to return to the vehicle mileage)
2. Hold the “O” button down till you hear a beep (could take a while, 30 sec.)
3. Press the M button repeatedly and a number of reset menus will appear, (If you have used oil according to quality sheet 229.31 or 228/229.51 you can scroll to Reset.31 or Reset.51 respectively.) Select “reset 51”
4. Now, when appropriate oil type is selected press “O” for 6 seconds until ”2” is displayed.
5. Press “O” once again briefly and the ” reset done” message will confirm that the job is done.
6. Pull the Key out
FOR THE 2004 DODGE SPRINTER!
Turn the key to position 2 in the ignition lock and immediately press the button MI (km) twice.
Within 10 seconds, return the key to the 0 in the ignition lock.
Press and hold the button MI (km). Turn the key to position 2 in the ignition lock. Keep the button MI (km) pressed.
The maintenance indicator with the time/distance is shown.
After about 10 seconds, an acoustic signal will sound and the maintenance indicator is displayed with the new remaining time / distance .
Release the button MI (km)